ek xres 3d models
567 3d models found related to ek xres.thingiverse
I needed a way to mount 2 EK-XRES Revo pumps in my Lian Li PC-O11 case. NOTE: This does not line up to any existing holes, you will have to drill and tap new holes in your case. ...But that shouldn't be a big deal, this is a computer mod :)
thingiverse
Adapter for the EKWB EK-XRES to attach it to the 120mm fan holes in the radiator with minimal airflow restriction. Goal was to get it LOW and CLOSE to the rad, but could be inverted to raise the pump up up a little. ... It uses the screws and washers...
thingiverse
Updated EK XRES DDC Pump/Res combo mount I have updated the mount I posted here 2 years ago, Will fit all EK XRES series pumps or any other DDC pump with a 5x5 mounting pattern. ... Can be mounted either way up, the photo shows how i intended it to be...
thingiverse
This is a 140mm fan mount for the EK XRES REVO D5 series of pumps / res. Mainly created to fit this to a lower point within my S340 case but is generic for all 140mm fan / radiator mount points. ... ** NOTE : Print with the 4 cut outs facing...
thingiverse
This is a 120mm fan mount for the EK XRES REVO D5 series of pumps / res. Mainly created to fit this to a lower point within my S340 case but is generic for all 120mm fan / radiator mount points. ... ** NOTE : Print with the 4 cut outs facing...
thingiverse
The hole dimensions match for a EKWB EK-XRES SPC/DDC. The mount frame holes are designed to use a PC fan screw. Be careful that it wont break, while youre screwing it in. ...I recommend to prescrew everything once in the first place, before you...
thingiverse
Mount for EKWB X-RES Revo D5 and 120mm fan with standard mounting holes (4.5mm).
thingiverse
This mount for EKWB x-res revo d5. I used 3m tape to install. ...Print Settings Printer Brand: FlashForge Printer: ...
grabcad
Just a little Adapter Plate for the EK-XRES to gain some clearance
thingiverse
This is a bracket made to hold an EK-XRES 100 DDC watercooling pump. Though any case could be drilled out to mount, this will directly bolt up to a hard drive bay for a be quiet! Dark Base Pro 900. ... Things to fix: - Tighten measurements between...
thingiverse
I couldn't find a decent Pump Mount file online for the EK EXRES series of Pump/Res Combo units so i decided to design my own, will fit any of the EK EXRES Pumps as well as any other DDC pump that uses a 5x5cm mounting hole pattern. This one is to...
grabcad
This is a 3d printable model for an extra holder for a reservoir tank for computer water cooling
grabcad
... mounting adapter for pump and combo unit installation. ...It is compatible with EK-XTOP Revo D5, EK-XTOP Revo DDC, EK-XTOP SPC pumps and EK-XRES Revo D5, EK-Xres DDC, EK-XRES SPC combo units. ...The bracket mounts to any 140mm fan hole pattern.
grabcad
... mounting adapter for pump and combo unit installation. ...It is compatible with EK-XTOP Revo D5, EK-XTOP Revo DDC, EK-XTOP SPC pumps and EK-XRES Revo D5, EK-Xres DDC, EK-XRES SPC combo units. ...The bracket mounts to any 120mm fan hole pattern.
thingiverse
These is a custom made low profile mount for the EK XRES 140 since I needed a mount for my case, designed to work without or with the rubber feet, in my case without due to how little room I had. ... I also made an adapter for the diffuser that lets...
cgtrader
A model of the EK-XRES 100 Laing DDC 3.2 PWM Elite, a PC water cooling pump and reservoir. This is an external model only, no internal electronics modelled. Useful for planning and rendering custom PC builds or mods. Dimensions measured from the...
cults3d
A simple pump mount for an "EK-XRES 140 Revo D5 PWM" Pump to fit in my "Obsidian Series® 650D Mid-Tower" PC case. Unless you have the same case and the same pump you might want to modify the design. I included a IronCAD file so you can modify the...
thingiverse
A simple pump mount for an "EK-XRES 140 Revo D5 PWM" Pump to fit in my "Obsidian Series® 650D Mid-Tower" PC case. Unless you have the same case and the same pump you might want to modify the design. I included a IronCAD file so you can modify the...
thingiverse
This is an adapter that I made up to mount an EKWB XRES to a radiator/fan using their X-Res X3 60mm holders when using their fan vertical pump mount.
thingiverse
... of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: font_spacing = 0.81 word = EK-_lHavoc- pen_length = 150 font_scale = 1.9
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=290279 Instructions Using the following options: font_size = 7 use_base = Yes text = EK resolution = 100 ring_width = 5 base_length = 18 use_childrens_cut = No ring_thickness = 3 ring_size = 65...
myminifactory
A wearable Badge saying "Ek Number" . Scale down the file as required. We suggest to scale it to half. This will give a a diameter of approx 50 mm which is wearable and will look good too. Lets see what more creative ideas you can apply on the...