elegoo smart robot car 3d models
162355 3d models found related to elegoo smart robot car.thingiverse
Just a quick printable design of a stand for the elegoo smart robot car.
thingiverse
Camera mount for a Pixy2 camera on a Elegoo Smart Robot car Mounts to front of vehicle using existing screws from the line tracking sensor. ...(See photos) Printed on a Prusa i3 MKS3+ in PLA Sliced on Cura Print Settings: Layer Height 0.2mm ...
grabcad
Kit robot with line tracking module and ultrasonic sensor mounted on a servo motor.
youmagine
I purchased Elegoo Smart Car Robotics Kits for each my two boys for Christmas. It is a good opportunity to teach them Arduino programing. The Elegoo BLE software let's them design json scripts the robot can perform from a phone. But my oldest said it...
thingiverse
This is a smart robot car that will sense if it is close to an object. When it senses an object, then it will turn and run in another direction until it senses another object. * Note- holes were left out of the car chassis for mounting the arduino...
cults3d
... Because of the PCB we designed, we made the necessary paths for you. What are the features of the 4WD SMART ROBOT CAR? ... Bluetooth Control Obstacle Avoiding Line tracking - following Ultrasonic distance https://www.youtube.com/watch?v=Vb2kd5qp2LA
thingiverse
... we designed, we made the necessary paths for you. What are the features of the 4WD SMART ROBOT CAR? ... - Bluetooth Control - Obstacle Avoiding - Line tracking - following - Ultrasonic distance https://www.youtube.com/watch?v=Vb2kd5qp2LA
thingiverse
I made it because after some searching on Thingiverse I couldn't find a simple chassis for a 3 wheel robot car. It's got a section for mounting a couple of small breadboards side by side. I also tried to add some struts to cut down the printing time....
thingiverse
This is the part to replace the third wheel of smart robot car from banggood: https://www.banggood.com/DIY-L298N-2WD-Ultrasonic-Smart-Tracking-Moteur-Robot-Car-Kit-For-Arduino-p-1155139.html?p=JH2514288496201309O3 Instruction of this kit can be found...
thingiverse
Leggere relazione allegata (Read attached report) date un'occhiata anche alla versione per la gara: https://www.thingiverse.com/thing:2782824 Lo scopo di questa prova è di progettare e realizzare un robot capace di muoversi autonomamente alla ricerca...
grabcad
This is the baseplate of the ZK-2 (2-wheel) version of the Uctronics smart robot car kit.Please note that these are usually made with a lasercutter, so dimensions might be slightly off compared to yours.
grabcad
Hobby "Smart Robot Car" skid loader type re-designed to have front steering. Electronic components modeled as used with a Dumbo RC Radio and Receiver along with other electronics. ...Most parts can be 3D-Printed, various small screws needed for...
cults3d
2WD smart car arduino robot chassis, to be used as reference for other designs remixed from various sources: https://grabcad.com/library/caster-swivel-wheel-40mm-heigh-2 https://grabcad.com/library/wheel-d65x25-1...
thingiverse
2WD smart car arduino robot chassis, to be used as reference for other designs remixed from various sources: https://grabcad.com/library/caster-swivel-wheel-40mm-heigh-2 https://grabcad.com/library/wheel-d65x25-1...
thingiverse
For this kit: https://www.amazon.com/Tracking-Chassis-Compatible-Projects-Raspberry/dp/B08FYBHQ4T/ref=sr_1_9?dchild=1&keywords=arduino+car&qid=1618425592&sr=8-9 Parts: 2X M3 bolts required Take a look at my website for other projects that I have...
thingiverse
Lo scopo di questa prova è di progettare e realizzare un robot capace di muoversi autonomamente alla ricerca di sorgenti luminose collocate in posizioni fisse e sconosciute all'interno di un campo di movimento di dimensioni assegnate che presenta al...
thingiverse
Made for the ELEGOO Smart Car Kit V3 Chasis only built to hold the Battery Case, Arduino Uno Board, Motor Control Board, and the four Motors. (Only the parts necessary to allow the car to move). The design was created with the purpose of making the...
sketchfab
The complete model of this Smart car was created from approximately 10-13 scans taken with Artec Ray long range 3d scanner from various positions around all sides of the vehicle. We kept 10 spheres (from a Laser Scanner Reference Sphere Set) in the...
grabcad
Smart CarUse Module ESP32 Cam to create a wifi hotspot and create a server to send data to the arduino.Arduino receives data from ESP32 Cam to control motor, ultrasonic sensor.Ultrasonic sensor HCSR04 measures distance and returns arduino.Solar...
sketchfab
... I have a better understanding as to how it works. Unfortunately, I textured before I smoothed the car, and therefore I am forced to re-do the texture; however, I might create a different car instead and texture that for more modeling practice.
thingiverse
Smart Owl Robot project. ...View it on Hackster.io here: https://www.hackster.io/gatoninja236/how-to-make-a-robot-chassis-fa8a45
thingiverse
Just a bumper with mount for 3 HC-SR04 sensor distance desinged by ssaggers http://www.thingiverse.com/thing:189585
thingiverse
This hexapod robot is a remix of 2 designs: * From the frame point of view we are using the hexapod robot model from markwtech: https://www.thingiverse.com/thing:3463845. In this implementation we are also using same cheap servo motors MG996R, but...