ender 3 pro y axis linear rail 3d models

**This is a work in process - parts are usable in current state** Included parts to upgrade your Ender 3 Pro from the POM wheels to linear rails on the Y-Axis. No more adjusting eccentric nuts under your bed! Compatible with MGN12H Linear Rails The...

This is a test by me to convert the Y axis of the ender 3 Pro to linear rail. For this i used 2x MGN12H 300mm Linear Rails some screws and a little bit of ASA filament. To fit the linear rails correct, i have made a tool:...

I saw H2FSpawn's model for Ender 3 Pro linear rails for Y axis and created it again with some tuning in Fusion 360 from scratch, just with simmilar dimensions as a previous one. In comparison to previous model, I have added 2 ribs to make the...

I saw H2FSpawn's model for Ender 3 Pro linear rails for Y axis and created it again with some tuning in Fusion 360 from scratch, just with simmilar dimensions as a previous one. In comparison to previous model, I have added 2 ribs to make the...

Print at 100% infill. You will want to install the stock bed carriage without the wheels on to these blocks. ...Keep all the bolts loose and then tighten them incrementally while sliding the bed fore and aft to ensure proper alignment and free motion.

While attempting to install a set of tech drawers (https://www.thingiverse.com/thing:3831119) into the front sections of my Ender 3, I discovered that the linear rails on the Y-axis were just a few millimeters too low to clear the top of the drawer...

I remixed the bracket from H2FSPawn and Warump because I dont rely on 3D printed threads. ...Therefor I added sink holes for M4 Nuts (connection to bed) and M3 (connection for y-axis stop). ... Hope you like it.

Endstop adapter STLs for the Funssor/PTCinder/probably other names Y-axis linear rail kit. ...Example listings: https://www.aliexpress.com/item/1005002628710810.html https://www.amazon.ca/PTCinder-Creality-Upgrade-ADAPTERS-Competent/dp/B0B5SZVQ5M/...

This is an MGN12 and 3 point bed leveling conversion for the Ender 3 Pro, it should also work on the OG ender 3 and possibly other printers that use a single 2040 or 4040 extrusion for the Y axis. I have included iges, step and fusion files along...

... use a very tight/high quality rail for Y. This allows the use of the blue annodized carriage direct onto 2x 300mm 12H linear rails. Edit - more elaborate V2 added. ...Adds some holes for self tappers to increase stiffness, as well as some ribs.

This is a fixed version as the original clashed. ...I could not edit that "Thing" so made another. See a photo of it in use on my Ender Pro with 2x MGH12 Rails.

Ender 3 V2 Y-Axis Linear Rail Bed Carrier Mounts No Drill - this is a remix on one side of someone else's mount that are very very good but left out the Endstop Paddle. Print one of each top side down on the bed. I looked high and low, these are the...

I designed this for my Ender 3 Pro with linear rail on y-axis to reduce the vertical ripples and to improve the stiffness in general and to also eliminate some resonances. You can adjust the Z height of the support to fit it in. Could also be...

This is a linear guide alignment tool for the Y Axis of an Ender 3 Pro. I bought the creality kit and they had a guide for the X Gantry and the Z but nothing for the Y Axis? I designed this so you print two of them and it should fit the extrusion...

This is a linear guide alignment tool for the Y Axis of an Ender 3 Pro. I bought the creality kit and they had a guide for the X Gantry and the Z but nothing for the Y Axis? I designed this so you print two of them and it should fit the extrusion...

Rear mounted case for a SKR 1.4 (Turbo) mainboard, a 40x40 fan and a Raspberry Pi in combination with the 3DFused Y-axis linear rail kit. The case consists of 4 parts to be easily printed on almost any 3D printer. ... For the connection between the...

An upgrade to fix the not linear Y Axis extruded bar

Y axis Linear Rail for ender 3 Series. Its not perfect. ...maybe you can contact me for i revised

Simple Ender 3 Pro Y Axis Linear Rail Upgrade Note – This is for the Ender 3 PRO ONLY I was looking online for an easy way to upgrade the Ender 3 Pro to Linear rails on the Y axis. With the 40mm width of the Y axis mount it looked easy to do and they...

... to any [3.3-5]v pin on the mainboard). Designed specifically for https://3dfused.com/product/ender-3-ender-3-pro-y-axis-linear-rail-kit/ but should be good for any setup (it's possible to use something like a piece of paper to trigger the sensor).

This is a remix of https://www.thingiverse.com/thing:2935204 Creality Ender 3 board fan guard by Admant77 After installing a 3DFused Y-Axis linear rail kit (https://3dfused.com/product/ender-3-ender-3-pro-y-axis-linear-rail-kit/) modification...

A simple bracket and support brace for installing a single 2020 V-slot linear rail support on an Ender-3, or any printer that uses V-slot extrusions. ... You'll need two of the RA brackets, and three of the small bracing plates..

this linear rail mount is for mgn9 rails and uses the original screws and belt. print without support, the two bigger holes have sacrificial layers so you dont need the support. print two of the spacers and press them into the bottom. ... the setup is...

It's suggested to add a modifier to make the part around the holes solid, or after a while the PLA will sag & let go, and the bolts will loosen making the whole bed unstable on the Z axis as in : you'll be able to twist it and rotate it...

**UPDATE** *I've adjusted the size to make for better tolerances, V1.1 .STL and .STEP is uploaded.* **DESCRIPTION** I completely reverse engineered and recreated da_syggy's Ender 3 Pro Rail Cover as it's not completely flat and straight. Otherwise I...

Y rail cover with more space for the full motion of the printbed. ...

Cover to fit into the end of the Y-rail suitable for the Ender 3 pro Y axis cover for Ender 3 pro

Ender 3 V2 Y-axis dual linear rail I'm using 2x MGN9 linear rail (length 300 mm) 2x MGN9H carriage block stock Ender 3 bed Parts to be printed: 2x mount_single.stl 6x support_plate_rail.stl 1x stop_extension.stl

When using the original Ender 3's narrow Y axis extrusion with dual linear rails, installing the limit switch becomes a challenge. This simple mount attaches with T Nuts and can slide fore and aft for fine tune adjustments. ... Mount is sized for 2ea...

Ok so i have seen a few Y Axis linear rail mods out there but they all seem to have a few things in common; + Loss of Z height + A number of printed parts and spacers + Quite a few holes to drill So mine is slightly different there is one printed...