ender 4 pro 3d models

This is a sliding box for the right-front space under the table on the Creality Ender 3 Pro. The Pro version uses a 40mmx40mm Y-axis rail. This will not fit (without modification) on the original Ender 3 with 20mmx40mm Y-axis rail. The stl files...

Housing for a BTT Octopus (Pro) on Ender 3 (Pro), with TFT35 V3.0, MOSFET and Raspberry Pi 4, 2ea 80x80x15mm Fan Only screws, nuts, washers and sliding blocks are required for assembly. Printed in PETG with 0.6mm nozzle. There is still room in...

Modified https://www.thingiverse.com/thing:4307348 to fit with my Ender 3 Pro double drawer https://www.thingiverse.com/thing:3548246 and remove the mount for the camera as I use a mount on the x-axis https://www.thingiverse.com/thing:3868687. ... ...

This is a remake from the pmayer design, i need the 5º driver on my ender 3 pro all the box , are only weth no 5º driver so dont fit, or very low top litle cut to right side part and , top cover for fun Honeycomb SKR 1.3/SKR 1.4 Ender 3 Pro Case by...

Option for Raspberry Pi 4 behind Ender 3 screen

I take the lower case a make a cleaner version for the RPi 4

Simple lid

This is the first thing I created in Thinker cad so constructive criticism is appreciated. This works for the LED-pinne bought at Jula. ... You can buy the lamp at: ...

Knob for Ender 3 Pro SIze 13x 3

... change it to put in rails to slide into the side of the chassis of the Ender. Confirmed that even though this is designed for Ender 3 Pro, it DOES fit my Ender 3 Max nicely. ... Same set of screws as the original design was used to put together

Looked around and found a really good page on installing Klipper3D on the ender 3 S1 Pro on [3d Print Beginners Site](https://3dprintbeginner.com/install-klipper-on-ender-3-s1-pro/). Followed his instructions and had the ender printing with all the...

Z-Achse in den Ender 3 einzubauen, da ich das ja bei einem Ender 5 schon mal erfolgreich gemacht habe. Da gab es nur ein Problem, ich habe beide Achsen über einen Treiber laufen lassen, was bei schnellen Drucken mit Z-Sprung zu unerwünschten Effekten...

Items on tinkercad here: https://www.tinkercad.com/things/dPB67qKLRoX This is a combinations Raspberry Pi 4, picam case and mount for the ender 3 pro (or other vslot printers). I am including the tinkercad so you can move the mounting plates to...

I used the following screws: * 8x M3X8 countersunk for the bottom and left and right * 4x M3x15 Flathead for the top * 4x M3x8 for mounting the SKR board to the base I''m not completely satisfied with the case fan design as the Ender 3 Pro has it on...

I used the following screws: * 8x M3X8 countersunk for the bottom and left and right * 4x M3x15 Flathead for the top * 4x M3x8 for mounting the SKR board to the base I''m not completely satisfied with the case fan design as the Ender 3 Pro has it on...

What a lovely idea - but it only fits to an Ender 3, not an Ender 3Pro... Of course I needed to change that :-D The design was made in Blender and I don't know anything about Blender. So I rebuilt the complete case with minor changes in Fusion 360. I...

Box pro základní desku Bigtreetech SKR 1.4 vhodný pro tiskárnu Creality ENDER 3 PRO. Nachází se vlevo dole Po tisku přidejte matice a šroub M3 šroub pro zajištění horního krytu a 30mm ventilátor k pravé stěně. Box for motherbase Bigtreetech SKR 1.4...

Remix of the Geekworm case Raspberry 4 wall/desk mount and the Ender 3 (Pro) rail mount slider (just one profile slot) - thanks to both of you! :-) This thing cleanly mounts the RPI4 in its case to the Ender 3 frame on the inner right side below the...

Back cover for the Ender 3 Pro LCD that includes mounting for a Raspberry Pi 4 (with dual mini HDMI ports and USB C power) along with a 30mm fan that can easily be powered directly from the Raspberry Pi's GPIO pins. ... This is great for being able to...

The case mounts directly to the side of the Ender 3 S1 Pro, replacing the factory display mount. The display then mounts on top of this case. Enhancements : - It offers a higher angle for the display. - It has a downward facing fan...

It is meant to sit in between the LCD and y axis extrusion, like the Ender 3-V2's tool drawer. The Pi will sit upside down in the case, so that print debris won't get in the way. And there is mounting for a single 30mm fan. It does include space...

The case does fit on the original case place on the E3 Pro, its just a bit higher and has more lenght. The original 4010 fan from creality is working fine on this. Mosfet Board with 70x45mm fits. The spacers are for the M3 screws if they are too...

Furthermore, the original design featured 4 standoffs to support the PCB, which does not fit with the bottom heatsink. This design features one support for the bottom heatsink. Lastly, the fan mount was removed as the raspberry pi with a heatsink...

This model lowers the IO holes and standoffs for the Raspberry Pi 4. I needed this to fit a small extra component inside the enclosure. I've printed this and the Pi still fits perfectly! ... No supports needed to print if oriented like the original...

Mont for raspberry 4 as LCD cover Spin-off of https://www.thingiverse.com/thing:4095160 The original one is difficult to install due the screw position. I split into 2 parts to simplify the installation. With this you can install the main case...

This is a remix of the LCD Enclosure by @eoyilmaz. I adjusted the number of ports available, also lowered the PI location so that I could add a mount for the fan. I also added posts for a Buck Converter. **Note: I have not printed this yet,...

This is a simple remix of drakaz design adapted to the Raspberry Pi 4 Model B (original was for Pi 3). ... I also added 2 holes in the back to integrate: - a push button to start/stop the Raspberry Pi - a Led to have a feedback on Raspberry Pi status I...

This is a simple remix of [drakaz design](https://www.thingiverse.com/thing:4417133) adapted to the Raspberry Pi 4 Model B (original was for Pi 3). ... I also added 2 holes in the back to integrate: - a [push...

Remixed to fit a Ender 3d Pro using a MKS Gen V1.4. ...I haven't printed yet for test fitment but should fit fine.