esc protectors 3d models

Printable ESC protectors for your WBX . Nice clean finish to your build and some protection. ...Print Settings Rafts: No Supports: ...

ESC protectors for [DemonRC Fury 5X](http://demonrc.eu/product/drc-fury-racing-purex-acro-fpv-frame/) frame. They should fit most 30A ESC. Attach to the arm with single zip tie. Broken case can be replaced without removing the ESC or motor. ... More...

Summary *** I designed many ESC protectors over time but these are my favorites, especially Model A. They are designed for Holybro F3 Metal ESC (the LED variant) but they will work with almost any ESC 17mm wide (the "NoLed" variant). It should...

A perfect ft for Chaos 20A ESC's, normally snap out the bottom bits so you can add or remove this cover whilst the ESC is wired in. ... kept my ESC in the shrink wrap it came with and mounted on some self adhesive foam.

These escs have been discontinued by Airbot. They are no longer producing this version because they found that they can send a voltage spike to your motors and fry them.**** I have since replaced mine with Kiss 24's I had in my parts bin. No more...

Protectores de varidores para el modelo de frame "TBP x5" de los fabricantes de Allcomposites. Piezas diseñas especialmente para este frame. A medida, siempre y cuando se pueden rescalar para adaptar a otros tiemos de frames y variadores. Todos...

Simple ESC protector, with and without a cutout for an RX wire if you want to mount your RX wires Bardwell-Style. Best printed in Flexible filament with the top side facing down and a brim. ... Inside width is 18mm, if you need it to be wider or more...

My take on an ESC protector. This is designed to fit over a Racerbee 30A ESC and should comfortably fit anything smaller. Small slots to let some air in and zip tie channels to keep it in place. Clam-shell design keeps your ESC safely off the carbon...

Set of ESC protectors for CarbonBird Scarab Knife 200 quadcopter

Canopy and ESC protectors for the Usmile UX5 quadcopter. It allows for rear facing power connector and top mounted VTX. The FPV mount is designed for the original RunCam Swift. ...It uses two of the 35mm standoffs provided in the UX5 kit.

work in progress. print with tpu 0.2 print open side down on glass to make bottom smooth so tape will stick Antenna channels included for rear of arms well. ... the open gap will allow rgb led's to run center of the frame arms enable supports, bed...

ESC protector for Armattan Badger

Fits XM20 size ESC, Racerstar MS25A etc..

My take on quadcopter ESC protection. ... Will recommend printing with flexible, but probably will work with PLA / ABS/ etc

Keep your ESC protected. This was designed to 18mm arm thikness, like Realacc X210 (on the photos)  Windows make it lighter and ventilated for happy MOSFETs. ... 1.63 grams each (printed with Watson filament) 

An ESC protector for Realacc X210 Pro 3K

Just my design of an ESC protector for an fpv drone. ...Super Simple and useful.

Just a KISS 24a ESC protector Prints it in TPU for better resistance

ESC protector printed on blue TPU for Armattan Chameleon / TI Nozzle 220 ºC Speed 30 mm / s Fill 20%

This Esc protector fits perfectly into the frame, it fits both modern and small. ...Internal space is 14x8 mm

ESC protector made specifically for Armattan Marmotte frame and Airbot Wraith ESCs, but can match similarly sized ones. Dimensions: 42x52mm. ... To be printed in elastic material.

This Esc protector is designed to fit perfectly on the arm of the QAVX or X210. ... Link to Top Plate: https://www.thingiverse.com/thing:2937002

1 piece full ESC protectors with Zip the slits, that have a layer under the ESC so its not sitting on carbon, and open up to slide over pre-wired ESCs.

This ESC protector has exteded tab to cover the weld pads. This feature is welcome especially in wet days. ... It will fit well in arms up to 15mm large.  Print - Protect and keep flying! 

Other ESC protector I made is mounted on top of the arm. That one can also be found on Thingiverse, but this one is my favorite. Inner size is 20 mm. So bigger ESC's will fit in. Benefit is that you can strap the protector down very well with a...

I have designed this ESC protector for my 30A LittleBees as I have lost several ESC's due to prop strikes and now that I have a 3D printer I can make something more elegant than old props taped over my ESC.

ESC protector for the 35A Betaflight ESC. Mountable with 2 small zipties through the cutouts.. Print with the flat (top) side down, no supports needed. Best printed in TPU, more infill will make it tougher, less infill will make it lighter. ...I...

After bent props destroying a few of my RG20 ECS's as well as constantly breaking the ESC protector version I found on Thingiverse, I took a stab at making my own. A TINY bit lighter than some others on here and stand up to a bashing even better!

Just another esc protector that fits in the realacc X210 frame, but now with a little drone logo. Printed in PLA with 0.2mm and infill 20% it weights about 2.56gr. Dimensions: Length: 34.5mm Width: 22mm Height: 13mm Thickness: 2mm ...

Just another esc protector that fits in the realacc X210 frame, but now with a little drone logo. Printed in PLA with 0.2mm and infill 20% it weights about 2.56gr. ... Dimensions: Length: 34.5mm Width: 22mm Height: 13mm Thickness: 2mm Internal width:...