eskate 3d models
36 3d models found related to eskate.thingiverse
Mini remote case for the cheap chinese mini remote used for Eskates more info here: https://www.electric-skateboard.builders/t/mini-remote-case/89322
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/ee6bCIPNdgQ
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/ee6bCIPNdgQ
grabcad
Possible to buy on Hobbyking. The dimension for truck fixation can be slightly different. Universal motor mount, recommended belt HTD5M length 275mm. ...Bolts design used from max power
thingiverse
printed with hard tpu, flat side on the bed, no supports needed. ... LID needs to be cut and heat bendet to fit in the spot where you cut away the steering wheel (after removing the internals ^^) the lowest plastic tip, where the antenna is mounted in...
thingiverse
I tough I could share this model I made with tinkercad, it serve as a bumper for my DIY longboard. ... Front or rear depends on the board and it can be used as support for light as well.
thingiverse
The wheel-gear attachment i designed for my electric skateboard. I have been using this, printed in PLA, for a while without any durability problems. It is designed to be used with a max 15mm belt. Designed for the "CHEESE CHEDDAR 72MM 78A...
thingiverse
make a dropthrough flash light for the hummie deck. ...not sure if it'll work with other dropthrough
thingiverse
This parts are ends for the Trampa underboard battery tray for electric skate (this : http://www.trampaboards.com/underboard-trampa-deck-material-battery-tray-in-10cm-lengths-p-24340.html) I've updated the part with a slight angle for the curve of...
thingiverse
Wheels to print in TPU. Designed a bit tight to fit on 90mm wheels. Rear : Inner diameter = 88.5mm Outer = 102.5mm width = 56mm Front : Inner diameter = 89mm Outer = 103mm width = 62mm I recommend to warm the wheels in hot water to put...
thingiverse
Headlight and taillight mount for the Evolve Bamboo GTR S1. im sure itll fit a myriad of other boards. i used m3 hardware. it fits common headlights offered on amazon and ebay. one version uses a interference fit, its my least favorite, i think...
thingiverse
I modelled this for my custom built electric skateboard to house my FocBox, a BMS (from Bestech) and a radio receiver.
thingiverse
Here's my battery enclosure that I modelled for my custom built electric skateboard. ...This enclosure is design to fit two Turnigy Nano Tech Lipo batteries inside.
cults3d
Tired of bumps and discomfort with hub motors on my wowgo 3. Hubs made by rumpsvett https://www.thingiverse.com/thing:3746673. Rumpsvett also made other types of hub adapters so check him out. Put the other stuff together with some templates from...
thingiverse
Designed to use on my ESkate, this is a 10s 18650 battery holder, normal and mirrored version.
thingiverse
Mounts for the lights of my personal Eskate project. Feel free to remix. ...Has both old school and new truck mount patterns.
thingiverse
Another XT60 cap, this one with a lanyard and printed in flexi-filament. ...Pictured is xt60cap_Lanyard.obj Has hole attach lanyard with m3 screw. Print in TPU/TPE This is a good for an eskate xt60 charge port!
thingiverse
A snug-fit mounting bracket for Amazon Basics WP522B waterproof speakers. ...Holds the speaker very securely, for mounting to surfaces that vibrate or bounce. I'm using it to secure the speaker to the underside of my eskate.
cults3d
Foot Stop for Skate longboard or cruiser Very useful on electric skate or longboard (eskate) because with acceleration, you tend to lose your balance... Attaches to things with the original screws. ... Diagonal placement possible, depending on the...
thingiverse
Intro: This is a Davega X eskate telemetry module mount for the Propel Endeavor Pro/S. READ THIS: There are 2 versions of the base plate, one sloped at 25 degrees (MOD 2 V2) and one sloped at 15 degrees (MOD 2). The 25 degree slope base will...
thingiverse
Replacement charge port cap for Evolve GTR eskate, and possibly others. Print in flex/TPE/TPU, something with some flex and GOOD layer adhesion. You don't want to tear it along the Z when you pull it off, and leave a chunk stuck in your charge...
thingiverse
Replacement charge port cap for Evolve GTR eskate, and possibly others. Print in flex/TPE/TPU, something with some flex and GOOD layer adhesion. You don't want to tear it along the Z when you pull it off, and leave a chunk stuck in your charge...