euc stand 3d models
153262 3d models found related to euc stand.thingiverse
The EUC_Stand_xx.stl versions are intended to be more universal, while named versions, such as the KS16S_Stand_xx.stl. Choose the base width that goes with your EUC. 19cm version is about the same width as the original stand from EUCGUY, and 18cm and...
thingiverse
EUC stand, perfect for sherman no supports needed 0.4 60-40 infill PETG(recommended) or PLA IF YOU WANT TO MAKE ME A DAY paypal/revolut: @madenssq
thingiverse
I kept breaking the other EUC stands due to the gap being too wide... so I made a wee stubby one. ... *This has been specifically design for a V8* Enjoy
thingiverse
I couldn't find any stands here on Thinigiverse for my Begode EX so I remixed EUCGUY's EUC stand 2.0 and stretched the stand in all directions (wider and taller) while keeping the screw holes intact. Same screw holes for Everbilt 1/4'' - 20x 1-1/4''...
thingiverse
End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515
thingiverse
Remix of EUC STAND 2.0, reconfigured to fit my Airwheel x3 and be printable in my small 3D printer. The stand will print in two pieces which fit together. This allows for printing in small printers like my own, which has a limit of 14x14x14 cm...
thingiverse
... for actual S18 dimensions. Assemble with 4x nylon M6 nuts and 4x M6 x 20mm hex head bolts. Tested with 3 walls, 20% infill PLA to support well over 100 lbs. PLA or PETG should work fine. My final stand I printed in PETG with 40% infill, 4 walls.
thingiverse
... Note! All the files are the same. i just uploaded all the models. Thanks to Shawn Duffey : https://www.thingiverse.com/duf67/about I know that the older stand would 10",14",16",18" and 22" wheels. This new version is the same in that regard. ...
thingiverse
... this in the near future but will not reprint since I am happy with how it turned out. I also don't need mine to come apart so glue is fine for me but I understand if you want a secure stand that pulls apart. ... Let me know how yours turns out.
thingiverse
This is the part that goes on the edges of the EUC stand so that it doesn't damage your floor. Remade it because the rubber is fragile and crumbled apart. ... https://alienrides.com/products/auto-latch-euc-stand
prusaprinters
A robust and pretty stand for an EUC (Electric unicycle), specfically for an Inmotion V5F.Instead of lifting the 11 kg and carefully putting it on the stand being worried about breaking the print…Don't lift it… just ROLL IT IN like a boss!No support,...
thingiverse
... the empty holes. ... This is for the larger wheels, so if you want to use it on the smaller wheels, you'll have to squeeze the stand in a bit. ... I tried it with smaller wheels and it's too wide, so the wheel just falls in between the two supports.
thingiverse
I modified "frame_2_fixed" by increasing the length by 1cm to make a better fit for my Gotway MSP (M Super Pro).
prusaprinters
A robust stand for an EUC (Electric unicycle), specfically for an Inmotion V5F.Instead of lifting the 11 kg and carefully putting it on the stand being worried about breaking the print…Don't lift it… just ROLL IT IN like a boss!No support, no raft,...
thingiverse
Remixed the Begode EX stand to perfectly fit a Gotway Monster Pro and clean up some self-intersecting surfaces which caused slicing issues in Simplify 3D. Use these screws with the appropriate 1/4" nuts. ...
thingiverse
I designed this S18 stand to be printed in one piece. It should fit most smaller printers, with a Z height of just under 195mm, and about 180x180 on the bottom. One piece is very good because there's a lot of strain laterally as you're putting the...
thingiverse
... parts are very strong. I've included a model for smaller frame specifically for my V8F wheel, but you can freely stretch the width of the model to fit your EUC. You can not stretch the height of the sidewall without impacting the screw holes. ...
thingiverse
The original model would fall over sideways unless the wheel was perfectly aligned. ...I gave it a wider base and changed the bolt holes to all be M4x30mm, shorter bolts will also work.
thingiverse
Still working on it. ill update here later. Update 03.12.2017: The space inbetween the 20mm pvc tubes are plenty for a Msuper v3. Soo, someone wanted me to create this and so i did. should be easy to print and put together. Use M7 screws...
prusaprinters
<p>Remix of this <a href="https://www.thingiverse.com/thing:5362850">thingiverse model</a><br>The original would fall over sideways unless the wheel was perfectly aligned. ...I gave it a wider base and changed the bolt holes to all be M4x30mm, shorter...
thingiverse
1) Cut up and made fit on FlashForge Creator (2 of sidewall_up.stl can be printed at a time since you'll need that many anyway) Print 2 of everything, join sidewall_up and sidewall_down with solvent cement, assemble with M6x30 bolts. ... ...
cults3d
Strong construction, works great in a combi car. The cool thing is that you don't have to carry the wheel. ...I have not tested on other wheels 8 screws are needed 4x 6M30mm 4x 4M40mm
thingiverse
Strong construction, works great in a combi car. The cool thing is that you don't have to carry the wheel. I have not tested on other wheels 8 screws are needed 4x 6M30mm 4x 4M40mm 0,4 I have 15% infill but it is not enough, use more than...
thingiverse
I like to park my unicycles upright. Mocked up to the measurements of an Inmotion V12 (from ground to bottom of the pedal hanger, at the highest pedal setting). Print Settings: Material: PLA Plus, PETG, or ABS Designed to be symmetrical. So...
cults3d
This is a front bumper stand for EUC Commander. ...Very stable as you can see a video that I linked.