fa 130 motor 3d models
100614 3d models found related to fa 130 motor.grabcad
Fully detailed model of one of the most commonly used electric motors.I 3d printed it and made it run as well. ...You can see it run here:https://www.youtube.com/watch?v=jkQwkZdAPX0
thingiverse
Mount for 130 size motor like FA-130 or FC-130 or the innumerable knockoffs. These are 3-9V direct DC motors popular for hobby use, with a flattened cylindrical profile like the above image. Don't expect to achieve a fit as nice as you get from...
grabcad
This is a CAD reproduction of the DC Toy Motor FA-103 (one of its many variants).The model includes all the parts and I tried to make it highly detailed. ...Hope it helps in your poject!
thingiverse
This is a very small part of someone who lost the DC motor stand. ...Motor model is Mabuchi FA-130RA serials. ...Use several M3 screws to fix the motor tightly and fix whole part to the board.
thingiverse
Slide-in holder for DC motor 130 ----------------------------------------- Tight fit without glue or screws. Just slide the motor in. ... The holes are 3.1mm for M3 screws.
thingiverse
I needed a motor mount for a few 130 DC Motors. Print them on their sides to simplify the supports. ... There are 4xM4 screw holes for connecting the mounts to your project.
thingiverse
This is a bilge pump I made for my RC boat that uses a 130 size motor, I also use it for water cooling in the boat. You may need to drill out the holes a little bit, and I just glued the motor to the housing but you could make holes for screws.
thingiverse
This adapts the ubiquitous 130-type motor to lego. The flange has to be glued to the motor and the axle adapter to the shaft. I made this to recreate the way Lego Technic kits with motors worked like in the early 80s. You had to create gearboxes...
thingiverse
A model of a small cheap 3-6V DC motor (130, I think). Not 100% accurate, but good enough to build a casing or otherwise integrate the motor into your project. I haven't printed it - so I cannot recommend settings. Maybe someone can use this for...
thingiverse
a blower for a 130 sized motor. mine came from a personal fan from walmart. comes with threaded adapter for npt 1/2 inch black iron pipe, threaded adapter is not npt, but works close enough with teflon tape. designed to be used as a forced air...
thingiverse
Tarot130 motor bumper. Must be printed with flexible filaments otherwise it will be impossible to mount! ... I used Filaflex @240°C, fan 100% Layers: 100um Weight: 6gr all 4 pieces, 30% infill
thingiverse
Real dimensions, simple 3d model to be used in small electronics projects with this very cheap micro motor. This model can be useful to consider right allocation. Please add your make or notify me for edits required. The picture shows the real...
prusaprinters
Tarot130 motor bumper. Must be printed with flexible filaments otherwise it will be impossible to mount! I used Filaflex @240°C, fan 100% Layers: 100um Weight: 6gr all 4 pieces, 30% infill Print Settings Printer: Hephestos2 Rafts: NoSupports: Yes...
thingiverse
FK-130 to FC-130 Motor Adapter for Slot Cars. ... Can be used as either Can Drive, or EndBell Drive. Note: The original motor mount will likely need to be slightly modified to fit the power wires from a FK-130 motor.
myminifactory
Another in my series of project using the small FA-130 Size motors. ... Read More about it here: http://www.skimbal.com/explorations-and-speculation/2014/12/22/small-motor-creations-6-orbital-gearboxes
thingiverse
Another in my series of project using the small FA-130 Size motors. ... Read More about it here: http://www.skimbal.com/explorations-and-speculation/2014/12/22/small-motor-creations-6-orbital-gearboxes
myminifactory
A Flywheel and casing, Design to work with the little Fa-130 size motor. ...Read More about it here: http://www.skimbal.com/explorations-and-speculation/2014/11/21/small-motor-creations-5-flywheelreaction-wheel
thingiverse
A Flywheel and casing, Design to work with the little Fa-130 size motor. ...Read More about it here: http://www.skimbal.com/explorations-and-speculation/2014/11/21/small-motor-creations-5-flywheelreaction-wheel
thingiverse
The Dart Thrower uses a FA-130 size motor to launch nerf N-Strike style darts. ...Read more about it here:http://www.skimbal.com/explorations-and-speculation/2014/11/7/small-motor-creation-2-dart-thrower
myminifactory
The Dart Thrower uses a FA-130 size motor to launch nerf N-Strike style darts. ...Read more about it here:http://www.skimbal.com/explorations-and-speculation/2014/11/7/small-motor-creation-2-dart-thrower
thingiverse
I designed this to hold 130/150/180 motors and it might fit more! It and a hole on the bottom for the motor shaft and two concave holes for motor mount screws. ...Enjoy :)
thingiverse
Shim I designed to use standard 130 size motors in the hyperfire conveyor gearbox. I designed cut outs on the sides for for the vents in the OOD Valkyrie. However, ended up using an old Rhino which isn't vented on the sides. Use at your own risk.
thingiverse
This is a very simple motor guard for the Ukiyo 130. ...Great mini frame design in Québec Canada :-) <a rel="license" href="http://creativecommons.org/licenses/by-nc/4.0/"><img alt="Contrat Creative Commons" style="border-width:0"...
prusaprinters
Shim I designed to use standard 130 size motors in the hyperfire conveyor gearbox. I designed cut outs on the sides for for the vents in the OOD Valkyrie. However, ended up using an old Rhino which isn't vented on the sides.</p><p><strong>Print...