fabrikator mini 3d models

Fabrikator mini v2 Fan

Webcam Mount for my Fabrikator Mini (Microsoft LifeCam Studio)

An ergo design Fabrikator Mini spool holder. ...Solidworks files included for your mods and improvements.

Printed on a large printer not Fabrikator Mini.This is a solid base to lift up the Mini and let air get to the electronics.

SummaryPrinted on a large printer not Fabrikator Mini. ...This is a solid base to lift up the Mini and let air get to the electronics.

Printed on a large printer not Fabrikator Mini. ...This is a solid base to lift up the Mini and let air get to the electronics.

... weight than you'd want to have hanging off your mini. This requires no post print gluing etc, it press fits onto the top lip of the fabrikator mini frame. How I Designed This Fabrikator mini 500g spool holder in onShape. ...https://cad.onshape.com/

... a little too low and they fall off when you move the printer. I designed these feet to fit perfect and won't fall off by themselves. The feet are 40mm tall. Print Settings Printer: Fabrikator Mini Rafts: No Supports: No Resolution: 0,2mm Infill: 15%

... Ø 52 mm, Width 45 mm). Printed in PLA 0.2 mm layer height, 20 mm/s, 20% infill => Time 1h:50m Please leave some feed-back, if it works for you (or not). Print Settings Printer: Fabrikator Mini Rafts: No Supports: No Resolution: 0.2 mm Infill: 20%

... from the printer. Print Settings Printer: Fabrikator Mini Rafts: No Supports: No Resolution: 0.2mm Infill: 20~35% Notes: Printed with Repetier, Sliced with Cura, on my Fabrikator Mini. ...Settings: 0.2mm, 20mm/s, 20~35%, no raft/supports needed.

Replacement extruder body for Fabrikator Mini from HobbyKing. I've straightened the filament path so it doesn't have a kink in it as well as filled in the gap after the extruder drive so there is no room for the filament to bunch up. Uses all the...

Since the printbed on my Fabrikator Mini cracked a week into its lifespan, i asked a friend to cnc this puppy properly out of a (scrap piece) of 3mm aluminium. Fits perfectly! ...I "designed" this in Tinkercad, dxf by NRG CNC (www.frontpanels.de)

Little hook that attaches to the fabrikator minis side panels. I printed 2 to use to hold a set of tweasers that I use all the time. Super simple, but strong. Be sure to print it on it's side so you don't need supports. ...It's a good simple print to...

... this because I have other screw heads which collide but some have success with just this. Your mileage may vary. Print Settings Printer: Fabrikator Mini Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: Any Infill: 100% for maximum strength

The Hobby King Fabrikator Mini is a great printer but it does not come with a print cooling fan so I designed some small clips to mount a 120mm fan to the front plate. ...I designed it in inventor and there was an issue with the mm to cm conversion so...

This is a large base for my Fabrikator Mini. It uses (2) 120mm fans, one below to cool the electronics and on on the left-hand side for part cooling. It has feet in the back to prevent tipping when using a 1kg spool. The front has a spot for the...

120mm fan system for the Fabrikator Mini by Tinyboy

Filament guide for Fabrikator Mini 2/Malyan M100

Summary 120mm fan system for the Fabrikator Mini by Tinyboy

Fabrikator mini-II Spool filament.www.caron.ws

Print Settings Printer: Fabrikator mini V1.5 Rafts: No Supports: No Resolution: 0.2mm Infill: 15% Notes: I am using Repetier Host with Cura Slicer with PLA Filament. Set Support Type to " none", Quality to "0.2mm" . ...It will take 4 Hr to make on the...

Another simple mounting solution for the Fabrikator Mini V1.5, to hang a common double relay module from the top edge. Category: 3D Printer Accessories

Another simple mounting solution for the Fabrikator Mini V1.5, to hang a common double relay module from the top edge.

Spool Adapter for Turnigy Fabrikator mini 2 There will be a second "Thing" later. ...A Spool Adapter need a Filament Guide.

... Pi 2 to my Fabrikator Mini so I came up with this, should be compatible with the Raspberry Pi 3. ...Print Settings Printer: Fabrikator Mini Rafts: Doesn't Matter Supports: No Resolution: .3mm Infill: 20% Notes: Printed in Hatchbox Red PLA at 195C

A simple 120mm fan mount for the Fabrikator Mini. Designed to fit in www.thingiverse.com/thing:1398468 This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3BNfajLHJe4

This is a cam-holder-mix for the TinyBoy/Fabrikator Mini printers. There are three different holders included: tripod mount HTC Sensation Logitech C270 This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/d9lkJAlC4Lz

Very simple holder for mount LED. ...In my case this is LED strips (3 LEDs) Print Settings Printer: Fabrikator 3D mini

SummaryNeeded something to mount my Raspberry Pi 2 to my Fabrikator Mini so I came up with this, should be compatible with the Raspberry Pi 3.Print SettingsPrinter: Fabrikator MiniRafts: Doesn't MatterSupports: NoResolution: .3mmInfill: 20%Notes:...

Here's a tool I designed in Tinkercad to rewind the Mini Spool for the Tinyboy/Fabrikator mini which you can find here: http://www.thingiverse.com/thing:1073340 I used a long screw and attached to a drill for easy refilling of the spool... ...Print...