filament spool size 3d models
665292 3d models found related to filament spool size.thingiverse
For spool size 126mm x 70mm but this model could easily be scaled to fit other filament spools as well. Axis diameter: 10mm Max Width (inside): 73mm Height (table to upper side of the axis): 84mm Instructions Print 2x of part 1 Print 3x of part 2...
thingiverse
Picture shows filament on spool after printing the Marvin and the 1 shell temp tower. Instructions Printed on 3 shell and 20% infill. No supports should be necessary as it was designed to not be...
thingiverse
Ender 3 M8 Universal Spool Size Holder Requirements: Stock hardware 4 x 608ZZ Bearing 1 x m8 threaded rod 5 x m8 Nuts I make this to accept any spool hole size with as little resistance as possible. As you can see on the cutted image the order is:...
thingiverse
... filament. I use these for holding samples of filament as well as the leftovers from larger rolls. The tubes for holding the filament start/end are sized to accept 1.75mm filament. Print each half flat. They should screw together easily. ...
thingiverse
Filament spool of similar dimensions to the ones supplied with the Ormerod. Inspired by film and tape reels coupled with the need to be able to see how much filament was left. Instructions Just print...
thingiverse
Choose a length for the threaded rods to match your spool sizes. I cut mine to 180mm long and 140mm wide. Assembly: Assemble two sides using the top holes in the feet. The order for a side part is: nut, washer, foot, washer, nut, [space], nut,...
cults3d
it is simply the stock anet a8 spool holder but double sized to allow 2 spools to be held at the same time. you need to print 2 pieces of each part in order to assembly it. you may also consider to print the spool holder i designed...
thingiverse
it is simply the stock anet a8 spool holder but double sized to allow 2 spools to be held at the same time. you need to print 2 pieces of each part in order to assembly it. you may also consider to print the spool holder i designed...
prusaprinters
it is simply the stock anet a8 spool holder but double sized to allow 2 spools to be held at the same time.you need to print 2 pieces of each part in order to assembly it.You can find all my models here, thank you who will appreciate with a download...
thingiverse
This is my interpretation for modular filament spool holder, my issue was that pretty much all filament holders had to be hung on the wall and you cound't put it on table or shelf. Also spools have different sizes so I made this one modular and...
thingiverse
If you have problems with poorly spinning filament spools, this is the solution. It fits into the most sizes of filamt spools (inner hole diameter max. 54mm). It adapts to the inside diameter of the filament spool! It fits all rods with a...
pinshape
Summary A remix of http://www.thingiverse.com/thing:2221206 clip set: Sometimes it was not obvious which clip I used for which spool, so I had to stack the clips next to each other to find the right size. These are labeled on the side, so you always...
thingiverse
A remix of http://www.thingiverse.com/thing:2221206 clip set: Sometimes it was not obvious which clip I used for which spool, so I had to stack the clips next to each other to find the right size. These are labeled on the side, so you always know...
thingiverse
Replacement for filament spool holder with adaptable internal spool size, from 25mm to 75mm diameter. All necessary parts are printed in around 7 hours at 60mm/s speed. Minitool included :) You need: 1 x M8 threaded rod (between 150mm and ...
thingiverse
Remix of the Excelfil spool holder that is wider with a thinner axle and some end caps (just in case) sized to fit Octave spools. ... Instructions I had to sand down the slots a little to get the sides...
thingiverse
Remix of the Excelfil spool holder that is wider with a thinner axle and some end caps (just in case) sized to fit Octave spools or Instructions I had to sand down the slots a little to get the sides to fit together.
thingiverse
Could not really find a simple, fully printed, freestanding filament holder to mount our ExcelFil Spools (32mm axle diameter, 20cm spool diameter, 6cm spool width) on the XYZPrinting Da Vinci. So here it is. Prints easy and snaps together by...
thingiverse
Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: .3 mm Infill: cone base plate 100% all others 30% Notes: I used ABS Post-Printing 1) Grab 1 skateboard bearing insert into filament spool base plate. 2)...
thingiverse
I'm using a larger Sterilite container for my dry box, the 54 Qt size, so I wanted a variety of spool sizes to accommodate as many spools as possible. BTW, do not buy containers on Amazon. This container was about $12 at Target and the even larger...
thingiverse
I bought 1KG spools of filament who didn't fit on the given mount of the CTC Bizer Dual Extruder, so I had to design a new one. With this one you can mount spools not thicker than 90mm and with a hole width not bigger than 30mm. ...CTC Bizer Series:...
thingiverse
This is a design for a spool holder, which uses the slot of an item 8 profile (40mm x 40mm). You´ll need an M4 screw and nut, to tighten the part to the profile. If you have any suggestions for improvement, let me know. ... Cheers Lasse
thingiverse
Yet another spool holder, this time it fit all filament 1-2 kg. spool See the Photo. It fit all spools from 29mm - 85mm center hole A mix of two existing project. I enlarged the center point and used the handle from...
thingiverse
This is a filament spool holder designed for different depth of spools =< 1 kg with three different hole sizes (50mm, 52mm & 54mm). It should be used with two standard 608 ball bearings (size = 22x7mm with core 8mm). ... Please be recommended to print...
thingiverse
Remix of http://www.thingiverse.com/thing:761893 Same exact shape, but each piece has been given a 3mm offset and hollowed out. This should (in theory) use less material to print. ...This is the base only, use the same axels from the original thing.
thingiverse
... Required hardware: Dual Setup: (see picture) 1x 3/8 threaded rod, 10 inch 8x 9/16 nuts 6x 3/8 washers 4x Spool_caps 1x Spool_holder_body 1x feed_tube_spinner 1x feeder *for M8 setup, replace all hardware with M8 nuts, washers, and rods! *Study Fig.
thingiverse
This is a adapter for the Robo 3D Top Mount Filament Guilde Spool Holder to fit 2 different robo3d spools. ... This is built to fit Robo 3D Top Mount Filament Guilde Spool Holder found http://www.thingiverse.com/thing:267039 Hope this is useful for...
thingiverse
Tired of adjusting your filament holder for each different spool size? We were too. Watch our YouTube video on how we made this! ... https://youtu.be/ljiYYKsMp5s CLICK THIS LINK FOR ASSEMBLY INSTRUCTIONS AND MORE DETAILS:...
thingiverse
I didn't like the less than smooth rotation so I made this one and sized it for the current Hatchbox, GizmoDorks, & 3d Solutech sized spools I have. (3/19/18) It also prints with a minimum of filament, which is a bonus! ... Layer height: .25 Filament...
thingiverse
I decided to remix the Spool Holder from cantizzy to get proper alignment with the filament intake of the MP Select Mini (Malyan M200). That way the filament can unroll even easier. I included the 123dx files from Autodesk 123D Design and also...