finderscope 3d models
126 3d models found related to finderscope.thingiverse
Solar Finderscope for telescope for Vixen style mount. No need to center the projection plane. ... No supports needed when printed on the Sun facing side Tape or glue a circle made out of paper or translucent plastic using the front side as template...
thingiverse
Also since I'm into astrophotography and have a guidescope mounted on top of my main scope which peers through between the focuser tube and the finderscope, that putting in a 15 degree tilt to the extender gives the guidescope a lot more viewing...
thingiverse
I made this finderscope no supports needed The internal diameter is 30mm. ...and the screw holes are for 3mm
thingiverse
This is a cap for finderscope for telescope with aperture size equals 30mm with 6x magnification. ... This type of finderscope is used general for SCT type of telescopes
thingiverse
This is a cap for finderscope for telescope with aperture size equals 50mm with 8x magnification.
thingiverse
A simple hood to put on front of your Skywatcher 9x50 finderscope to avoid condensation. ... Easy to put and remove.
thingiverse
Adapter for finderscope to DSLR Canon. Print both parts, screwed and glue together. Designed for square nut M4. ...new version in one piece support necessary
grabcad
While designing an adapter that could be 3D printed I figured I might as well model the entire Stock Finderscope Assembly.So here it is!The dimensions are taken from my own Finderscope so they may not be perfect for all, however, they are very...
thingiverse
Original holder is terrible, so I created a new one, which is much more firm and also can carry both optical finderscope and laser pointer. Some M4 screws and nuts also required! ...:) Main post can be found here: ...
thingiverse
This mount was made to attached [this](https://smile.amazon.com/dp/B08XMFWFG2?psc=1&ref=ppx_yo2ov_dt_b_product_details) finderscope to my Canon 550D. The holes take two M4 screws to apply tension on the finderscope. The flash mount is a little snug....
thingiverse
There are several green laser pointer holders on Thingiverse, but I wasn't sure which would fit my Orion 6x26 and 9x50 finderscopes so just made one in Fusion360. Made to fit snug and not come off so they do not clip around the finders like some...
thingiverse
Got tired of hurting my neck when using the straight finderscope that comes with my Celestron XLT150, so I challenged myself to create a right angle one. Results are great and no more back and neck issues. Note that this is not a Right Angle...
cults3d
This is a new upgraded version of my finderscope/guidescope adapters. I have made it so the threads for the thumbscrew are made of metal, giving it a more secure fit. I have also included the thumbscrew end that is optional to install on the screws...
thingiverse
This is a new upgraded version of my finderscope/guidescope adapters. I have made it so the threads for the thumbscrew are made of metal, giving it a more secure fit. I have also included the thumbscrew end that is optional to install on the screws...
thingiverse
Customized version of http://www.thingiverse.com/thing:2423779 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2423779
thingiverse
A simple finder scope for small telescopes. With the adapter it can be mounted on standard finder scope mounts. To combine the clamp with the main scope, a M4 x 10 screw is required. ###<u>***PrintedLabs***</u> Are you looking for exciting...
thingiverse
... reliable threads in the mounting rings - especially at this pitch, I wouldn't rely on tapped threads to last very long. The finderscope or laser pointer is suspended in place using 4-40 thumb screws (I'm using McMaster-Carr part number: 98704A125).
prusaprinters
This finderscope is designed to fit Orion telescopes. The part can be printed in place with no supports by laying the back panel flat to the print bed. Use PETG filament so that the part doesn't melt in direct sunlight.
prusaprinters
This is a replacement model for the bracket that goes on the Zhumell Z10 telescope to hold the finderscope. Despite testing the hole size for the tightening screw, after printing it turned out to be just a bit small for me. You may need to...
thingiverse
- Tested a full night in 10C garage at upright position dual mounted and finderscope and it survived. I needed a dual mount for holding my guidescope and finderscope on a single bracket. There was already existing models for this, but after...
prusaprinters
This is just an align-able interface for a 6x30 finderscope to help in aiming your Hadley (or similar) telescope. ... I attached mine to a Fracley.<br><br> </p><figure class="image image-style-align-left image_resized"...
thingiverse
Dual-ring bracket for 7x24 finderscope You will need: - 3x M3 screws (from stock bracket) - 3x M4 screws