finger board ramps 3d models

Teck deck for my son's finger skate board. ...Uses the standard connectors to extend his skate park.

This object was made in Tinkercad. ...https://www.tinkercad.com/things/5zPTuT9UAsR

finger board mini ramp, chopped to fit 200x200 printers. ...can print double or more of the parts to make a wider ramp.

This object was made in Tinkercad. ...https://www.tinkercad.com/things/e9fZmfSbb2P  i was inspired when I saw a video on YouTube that people were riding bikes in a half dome, that's why I came up with this design

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/9tSb6AYC7dV

This object is the TinkerCad design challenge

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/lQBrGuuKfiX

This object was made in Tinkercad. ...https://www.tinkercad.com/things/9BMEEgqUh6M

Hi, I don't think most people would like this it is my first thing on Thingiverse and this is not my best design I have been doing this for under a year.

mini finger skate boards ramps

Finger board ramp

This is a fun finger board that was made fro smaller fingers! ...beware that the inner diameter of the finger holes are 0.6 inches!

It's a 3d printed finger board. ...No the wheels do not move, but still fund to play around with 

finger skate 

wanted to make some more board for my son, so this was good practice for the drawing program. ...

allows for 2 fingers on either side or 2 from each hand in the middle if you have small hands you may be able to fit your whole hand. I recommend printing at a .2 layer height with 60%+ infill  for best strength and results print with the back...

RAMPS Testing Board

so i designed the ramps holder and associated bridge board to remove all the wire clutter that i had on the side. i now use a case with enclosed ramps and display.. makes life easier to transport and use .. fits any ramps/arduino mega shield ..

so i designed the ramps holder and associated bridge board to remove all the wire clutter that i had on the side. i now use a case with enclosed ramps and display.. makes life easier to transport and use .. fits any ramps/arduino mega shield ..

... you can make one too! The part that goes on your finger is 15mm (or .6 inches) because it is supposed to be printed out of TPU, it should fit many sizes. ...--I will design a bigger fit if anyone requests a bigger size!-- If anyone has any other

The Ramps Bridge Breakout Board was designed to accommodate all the cables associated with the printer and use a common harness which routes it to the controller which can be housed in an ice box. ... Available as KIT, Bare pcb or assembled.

The Ramps Bridge Breakout Board was designed to accommodate all the cables associated with the printer and use a common harness which routes it to the controller which can be housed in an ice box. ... Available as KIT, Bare pcb or assembled.

Just in case anyone needed a spacer for this ramps board to shift away 20cm so it will not hit your X-axis stepper motor as it is raising up in the z-axis This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jhqa6WlBumv

It was used to hold the Arduino and Ramps 1.4 boards in the bottom of the printer. Because the USB cable had to attach to the Arduino board and also be able come out in between the two sections of the 20x20 rail, the board holder was slanted up...

Instructions 1) Mount the body to the frame of your printer 2) Add the boards 3) Attach your wires. 4) Attach the door. Door is optional. It attaches with 5mm bolts. Both the case body and door have holes for 40mm fans. ...I have my top fan blowing...

snow board for your fingers

Cover for the stock Ramps 1.3 board on the Hictop i3 clone (2015 model).

This is the second model in the Finger Board Series!

This is the third build in the finger board series.

This is the third build in the finger board series.