flash forge creator pro 3d models

Flash Forge creator Pro coil holder. ... Smaller than the original holder.

These are for the flash forge creator pro to cover the handle holes on the side of the printer. ...They hold themselves in place with built in tab hooks.

Instructions I printed this on the Flash Forge Creator Pro using Hatchbox orange ABS. Layer height .2mm, extruder temp 235, bed temp of 110c, active cooling, glass bed with kapton. I found it prints just fine with no support or rafts. Sliced in...

Handle covers designed for the Flash Forge Creator Pro to retain warm air and/or reduce drafts during ABS printing. Easily add rare earth magnets to detents or just use blue painter's tape to hold in place. ...

Print Settings Printer: Flash Forge Creator Pro Rafts: No Supports: Yes Resolution: 0.3mm Infill: 15% Notes: These were printed using the black ABS supplied with the printer. ...I set the infill to 15%, however i think this could have been down to 5%.

Tool holder Designed to hang on Flash Forge Creator Pro Handles. They are stack-able as seen in the pictures. Print Settings Printer: Hictop Prusa I3 ...

... spool and getting tangled. The Creator Pro has a small opening in the back that allows access to some wiring. This piece fits snugly inside that opening. I use this along with this spool guide and Spool Holder to get the best possible results.

Print Settings Printer: Creator Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 15-25 Notes: The large radius around the surface allows you to print at a lower infill. The radius makes up the strength for low infill. ...Recommended printing...

This simple print will allow you to use the non Flash Forge Creator spools that do not have the indented area for the spool but that do have the big spool hole. By extending the length of the spool holder the spool will stay clipped onto the spool...

Plugs to seal the handle holes on the FF Creator Pro for when you're printing ABS and need to keep the heat in.

This is a spool for AMZ3D filament on the Flashforge Creator Pro. This is meant to be printed as two pieces and then joined by welding or an adhesive. ... Main Spool Ø = 31 mm

This is a spool for AMZ3D filament on the Flashforge Creator Pro. This is meant to be printed as two pieces and then joined by welding or an adhesive. ... Main Spool Ø = 31 mm

The Creator Pro normal attachment point for the filament feed is too close to the body of the printer. Without this offset, the filament can slip between the spool and the body of the printer and get stuck. Not good. This offset clips securely into...

... bottom of the guide holes are chamfered to ease inserting the filament. I also upgraded spool holders, see my other models. Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No How I Designed This Modeled in Fusion360

... It was too long and the spool walked back & forth. This version works great for HatchBox sized spools. I also upgraded a filament guide, see my other models. Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes

This spool holder is specifically designed for the Flashforge creator pro. However, the spool holder will fit multiple other similar printers. In addition, the spool holder can accommodate most spools, even up to a wider 2kg. The spool is...

Dial indicator mount for flash forge creator pro 2016. Useful for bed leveling Mount screw hole is 6mm Print Settings Printer: FFCP Rafts: ...

Flash Forge Creator Pro (2016) X-Axis Support Instructions Cable support for X axis of the flash forge creator pro. On mine the exposed wires would rub along the x axis guide rails. I wrapped them in some 10mm corrugated tubing and printed this...

This one is for a Flash Forge Creator Pro, I bought it in late 2016 and think the tube clips may be different than original versions which may be why the other models did not work. Print Settings Printer Brand: FlashForge Printer: FlashForge Creator...

This thing is a larger spool holder for the Flash Forge Creator Pro so that you can use larger reels with the factory mounting position on the back of the printer. This spool holder works with RigidInk 1kg Reels and adds a bit more flexibility when...

This ensures that a full spool will not pull off the side of the spool when in printing, as it will with many spools on the stock Flash Forge Creator Pro spool holders. It is also slimmer and longer, allowing for a wider range of filament spool...

Print Settings Printer: Flash Forge Creator Pro Rafts: No Supports: No Resolution: .27 mm layers Infill: 15-25 % Notes: Use 15% fill as a minimum since this will be supporting weight. No Support or Raft needed. Just slice and chugg. ...There is a void...

Magnetically detachable hinge for Flash Forge Creator Pro top hinge door model. I designed this hinge so I could easily remove the door for printing with PLA. This may also work for the side hinge model if you feel the need to remove the door. The...

It will accommodate 99% of spools.http://www.thingiverse.com/thing:1438914 This is a slot type spool holder for a Flash Forge Creator Pro. It will accommodate about 50% common spool sizes. I ordered some spools that had small diameter center holes so...

... the filament from coming off the spool and wrapping around the spool holder itself. I also added ledges so when snapped into the tube holders on the back of the Flash Forge Creator Series printers it does not move up and down within the clips.

... the filament from coming off the spool and wrapping around the spool holder itself. I also added ledges so when snapped into the tube holders on the back of the Flash Forge Creator Series printers it does not move up and down within the clips.

Summary Started with WiFi Cap For QiDi Tech 1 and removed the wifi logo then replaced it with a recessed SD logo. ...Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No How I Designed This Remixed using tinkercad.

These are a few components to help integrate a fume hood with the Flashforge Creator Pro. It includes some mounting studs and sealing plates for the back of the printer. The installation process should be obvious from the photos. ...M3 screws fix the...

These are a few components to help integrate a fume hood with the Flashforge Creator Pro. It includes some mounting studs and sealing plates for the back of the printer. The installation process should be obvious from the photos. M3 screws fix the...

After looking around and not finding anything good enough for me I made my own. It is designed to have 2mm plexi glass to protect the monitor from dust. ...I'm here to share with everyone!