flashforge 3d printer models
2253146 3d models found related to flashforge 3d printer models.thingiverse
This is a model of the Flashforge Dreamer 3D printer.
thingiverse
This is a model of the entry level Flashforge Finder 3D printer.
prusaprinters
This is a model of the entry level Flashforge Finder 3D printer. Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Doesn't Matter Notes: Rotate model 90 degrees on the X axis to minimize supports Category: 3D Printers
myminifactory
This is a model of the Falshforge Dreamer 3D printer
cgtrader
Designed to perfectly fit FlashForge Creator 3D printers, this clip prints as two separate pieces that can be easily snapped together to create a hinge with just the right amount of resistance. The clip file also comes with a snap bolt that is...
cgtrader
A fan shroud for the FlashForge Creator and Creator X 3D printers. Designed to fit perfectly and snap easily into place, this fan shroud will protect the exposed extruder fans from fingers and parts. ... www.parametrix3d.com
cults3d
So the Finder will not be able to sense when the spool runs out of filament and pause the 3D-print. If you are looking for a product that is not available, please contact us. To learn more about the FlashForge Finder and support. ...Please contact us...
grabcad
The model is the spool holder that the FlashForge Creator Pro 3D printer use to support the filaments
thingiverse
... be more than 2.5 mm thick. Print Settings Printer: FlashForge Creator Pro/ FlashForge Dreamer/ FlashForge Guider/ FlashForge Finder Rafts: Doesn't Matter Supports: No Resolution: 200 microns Infill: 15% Notes: 5 top layers and 5 bottom layers.
thingiverse
Print a 3D printer - Flashforge Finder Mock-Up.
thingiverse
Accessory to prevent air from entering the Flashforge Creator Pro 3D Printer port
thingiverse
This is the first printer in my model series 3D printers where I Model 3D Printers from scratch The Flashforge Adventurer 3 is my personal 3D Printer and is fully enclosed. the thing hanging out like a door is the door. ...I made this from scratch in...
thingiverse
I got my FlashForge Dreamer 3D printer recently. After few searches did not find a right hook for my GoPro camera and decided to make it myself. a) the straight mount is taken herehttp://www.thingiverse.com/thing:123878 b) the hook designed myself...
thingiverse
FlashForge Dreamer 3D printer hook for filament. I have created hanging hook for Nunus 1 kg filament which is not fitting inside the printer's cabin. I started from another prototype http://www.thingiverse.com/thing:938750 I have than designed and...
thingiverse
This is a remixed version of the External Spool holder for the FlashForge Finder 3D Printer by CreativeTools. This version allows you to mount the spool holder on the side of the machine. It prints in one piece on the FlashForge Finder, just have...
thingiverse
This is an external spool holder designed to interface with the Flashforge Inventor 3D printer. It may also work with the Flashforge Dreamer and the Dremel Idea Builder. In order to complete this project, you will require a 5/8 inch round wood dowel...
thingiverse
This is an external spool holder designed to interface with the Flashforge Inventor 3D printer. It may also work with the Flashforge Dreamer and the Dremel Idea Builder. In order to complete this project, you will require a 5/8 inch round wood dowel...
thingiverse
This thing allows you to install a spool with a hole of about 30mm to a CTC or Flashforge 3D printer. This is my first attempt to draw anything in SketchUp but it works. More photos are coming soon. http://youtu.be/B6HgoJb__j8 ...
thingiverse
This is a filament spool holder for Robo 3d Printer Filament used on the FlashForge Creator Pro. Although the spool holder was completely re-drawn, it was based on http://www.thingiverse.com/thing:930910 and we are inserting KDan's holder clip again...
thingiverse
This is an external spool holder designed to interface with the Flashforge Inventor 3D printer. It may also work with the Flashforge Dreamer and the Dremel Idea Builder. In order to complete this project, you will require a 5/8 inch round wood dowel...
thingiverse
These corner brackets were designed to interface with the Flashforge Inventor 3D printer and the glass plate upgrade from Flashforge USA. Supports glass dimension (L x W x H) 9 x 6 x 0.15 inches. Glass must be installed on top of the Flashforge build...
thingiverse
These corner brackets were designed to interface with the Flashforge Inventor 3D printer and the glass plate upgrade from Flashforge USA. Supports glass dimension (L x W x H) 9 x 6 x 0.15 inches. Glass must be installed on top of the Flashforge build...
thingiverse
Sorry I use a french Win10Pro, so the translation will not be the same On win10 -> This PC -> Connect a network drive Use the last line "Connect to a web site ..." a few next next next after Enter : http://FlashForge/3D with FlashForge = Your APPNAME...
thingiverse
Needed some rubber feet for the Flashforge Dreamer printer. Print this (x4) in SemiFlex (preferred) or NinjaFlex. Instructions Print with about 4 shells and 25% infill. SemiFlex or Zentoolworks Flex...
thingiverse
Models for printing: 1x Filament Feeder Head Support (3D Printed) 2x Dust Filters (3D Printed) 1x Active Cooling Fan Duct (3D Printed) Additional Parts needed: 2x M3-0.5 60mm, Class 12.9 Alloy Steel Internal Hex Socket Cap Screws 2X M3-0.5...
cults3d
For similar purposes, we have also designed free-standing spool holder: http://thingiverse.com/thing:508896 Please also see our Universal Cantilevered Spool Holder for 3D printers http://www.thingiverse.com/thing:2297303 ####By Creative Tools Home -...
thingiverse
DC-DC converter on Amazon http://www.amazon.com/exec/obidos/ASIN/B009HPB1OI/donscollecti LED Lights: http://www.amazon.com/exec/obidos/ASIN/B005EHHLD8/donscollecti I had to include an STL to publish a "thing", and I've been wanting to keep a couple...
thingiverse
If you happen to have PLA spools that don't fit inside the build-in filament casing, then this external spool holder makes it easy to fit them on your 3D printer. The holder's axle is hollow to accommodate one or more units of the Universal Filament...
cults3d
The filament spools I bought would not fit all the way onto the spool holder that came standard with my flashforge printer which have a 66mm x15mm spacer at their base. Unlike the spools that came with the flashforge which are countersunk to...