flashforge finder spool holder 3d models

Flashforge Finder Spool Holder designed in Catia. ...Simple and safest way to use as a spool Holder

I started with m1s2h3's flashforge finder spool holder thing and modified it to include a second hook that would house a filter on it. I modded the hook to flip the connector on it to the opposite side, then modded his filament feed guide to connect...

My own take on a spool holder for Flashforge Finder

A good spool holder for the Flashforge Finder printer

An universal spool holder for the Flashforge Finder. Slots over the back wall of the internal spool room, and allows any size spool (up to 70mm wide) to hang from the back of the printer. Simply open the door slightly and slide the holder onto the...

This is a Filament Spool Holder for the Flashforge Finder. I design this to be printed on the Finder and it was. I also designed it to be bolted together but I am guessing the it could also be glued together. ...It sits on top of the Finder and does not...

This is a side spool holder for the Flashforge Finder, the detachable spool pin can also be used with the Flashforge Guider in the side openings. Place the tower on either side of your Finder and slide the spool mount and removable end stop into...

This is a side spool holder for the Flashforge Finder, the detachable spool pin can also be used with the Flashforge Guider in the side openings. Place the tower on either side of your Finder and slide the spool mount and removable end stop into...

This is a custom made design to fit the FlashForge Finder PLA spools (0.6 kg), with two screw holes for mounting to a vertical surface. I printed the prototype with low detail setting and only 10% infill, which seems to be enough. Change your...

Note: The Flashforge Finder branded filaments will fit on this spool holder but you will have to take the spool rod out first because the spool wont fit over the lip on the end. Print Settings Printer Brand: FlashForge Printer: FlashForge Finder...

This is a side spool holder for the Flashforge Finder, the detachable spool pin can also be used with the Flashforge Guider in the side openings. Place the tower on either side of your Finder and slide the spool mount and removable end stop into...

This spool holder fit on the side of your FlashForge Finder, to be able to print any third party filament. The file fit in the diagonal of your build platform If you use a third party filament don't forget to untick the option "filament checker" in...

This is a spool holder for flashforge finder that works like a charm! It mounts easily on the back of the printer and stays in place. In my opinion, I think it works better than the spool holder inside the printer. It works for FlashForge Finder. ...

Replaces the entire filament holder cartridge on the back of a FlashForge Finder. ...Note that this upgrade will delete the filament out sensor.&nbsp;</p>

###Flashforge Finder 3D Printer Spool Holder The Finder is an affordable 3D printer for K-12 classrooms. However, it does not allow easy mounting of common spools. In designing this holder, I tried an existing one on Thingiverse (thing:1763329),...

This is my take on a good spool holder for my Finder as I really hated the stock option. Its either small spools or hang your spool elsewere, filament rubbing on the printhead and so on, many issues with the stock. There`s a "readme" document in...

Doesn't use a lot of filament! ...I recomend not changing anything on your slicer.

A spool holder for the Flashforge Finder with a built in filament guide. Simply slide the holder onto the back wall of the printer after lifting the spool compartment cover, and guide the filament through the hole. I have used this for many builds,...

There are plenty of spool holders already for the Flashforge Finder. I wanted one that I could do it all with one printing. Both of these can lay flat and print with no support. I used super clue to attached the arm. ... Would be nicer if it just...

# Introduction A spool holder for the FlashForge Finder, designed with low friction and modularity in mind. Apply bearing grease between the axle and bushing ("slide bearing") for really smooth running. Both the standard FF Finder tube and the...

... I Added the filament guide to the files and to the 123D Design files! Take a look at the new photos... it allows you to leave it in place while using cartridge. Print Settings Printer: Finder Rafts: Yes Supports: Yes Resolution: Normal Infill: 30%

This is a remix of a Flashforge Finder side spool holder with mount for Filler spool holder. ... Finder spool holder original source: https://www.thingiverse.com/thing:2065204 Filler - where you get the spool bar and roller:...

This is a remix of a Flashforge Finder side spool holder with mount for Filler spool holder. ... Finder spool holder original source: https://www.thingiverse.com/thing:2065204 Filler - where you get the spool bar and roller:...

This is a filament spool holder for the FlashForge Finder. Instead of pins like the one I'm remixing, I created a shuttle. ...I also gave it some curves and small embellishments.

Inspired by stibo (https://www.thingiverse.com/thing:3680561) and itech3dp (https://www.thingiverse.com/thing:2790290), this overhead spool holder is designed to print on the Flashforge Finder without supports. ...*This is a work in progress and...

This is a external spool holder for Flashforge Finder after an idea from https://www.thingiverse.com/thing:2971113 The holder is designed for 200x75x53 mm, in Sweden known as Clas Olson 1 kg PLA spools. You gonna need 4 M5x10 screws and 4 bearings...

I made some modifications so that it can hold makerbot spools with a lock cover from outer side. ...Print Settings Printer Brand: FlashForge Printer: Finder Rafts: No Supports: Yes Resolution: 0.18 mm Infill: 20%

Spool should unroll under and use the spool holder by CreativeTools to direct to your printer head. http://www.thingiverse.com/thing:751182 This is version 1, I'll want to make a second version that is thinner and also for the other side to hold...

This is an improved verion of another users filament holder.

I went back to the rear holder for awhile but a side mount solution really made more sense for my setup. I decided to try my own take on the idea. The first revision was basically the original design, just combined into one model and made a bit...