frag rack 3d print
2460982 3d models found related to frag rack 3d print.cults3d
Egg Crate Frag Rack Leg Set Includes Base : 4x4x1cm Top : 2,1x2,1x0,7cm Height : 18 cm Printing time 1 pcs : 3,2H's 3D Printed with High-Quality PETG
thingiverse
A simple frag rack for holding your corals. Fitted with angled suction cup holes so that even if they are loose they will not slip out from their position (even with super high flow tanks) This rack has sharp corners, Check out my account for a model...
myminifactory
The goal was to design a frag rack which should allow good flow between the plugs and promote growth, Dual suction cups for secure mounting and looks fairly nice but still robust. ... Frag Plugs used in picture :Top: 20mmStem: 10mm Suction Cups:Uniclife...
thingiverse
The goal was to design a frag rack which should allow good flow between the plugs and promote growth, Dual suction cups for secure mounting and looks fairly nice but still robust. ... Frag Plugs used in picture : Top: 20mm Stem: 10mm Suction Cups:...
thingiverse
Simple frag rack that holds 7 frag plugs. ... 50mm tall, prints very quickly, ideal for using to acclimatise coral frags while on your sand bed.
thingiverse
Small Frag Rack - printed with PETG, holds 6 frags and fittable dollarama ceramic magnets on each side of wall. ... ceramic magnet: https://www.dollarama.com/en-CA/p-clear-coloured-magnets-assorted-sizes-and-colours/3011612
thingiverse
Simple frag rack designed to use home depot magnets. The plugs should be printed solid (100% infill). I used the xenia plugs with a small shell on top. ...
thingiverse
A support column for holding up aquarium frag racks. I have had to print it solid at 100% infill to get it to sink. ...I'm using PET+.
cults3d
This small magnetic frag rack should be printed in petg for any aquarium use. ... Fits round coated magnets up to 30mm diameter
thingiverse
This is a frag rack that I designed to hold up to 10 3/4" frag plugs. I printed in PETG. It is designed to work with the suction cups shown in the photo. ... They are available from HomeDepot for around 2$ a pack.
cults3d
reef aquarium frag rack coral holder dimensions 77.5 x 150 mm for 10mm thick glass
thingiverse
Square rack for coral frags. ...Made to easily four of them in a 17" cube tank.
thingiverse
This is a mini Frag Rack, optimized for a Red Sea Reefer. It holds up to 5 small coral frags. ...Optimal for zoanthus and small corals
thingiverse
A basic frag rack for coral frags in a reef aquarium. 4x 12mm holes for the frag plugs. 2x 6mm holes for the suction cups. ... Some cheap 20mm suction cups from ebay were a perfect fit.
thingiverse
The rack is held by two magnets. ... Use old magnets. works also with frag plugs use PETG no PLA
thingiverse
Feet are 1/2" in Diameter by 1-1/4" tall, and hold the frag rack (Egg Crate) 1 inch above the bottom of your bare-bottom reef tank or frag tank. Print with 100% fill so the feet aren't too buoyant. Since it is tall with a small base, print with a...
thingiverse
A small 3D printable frag rack. All that is neede extra are some magnets. 4 x small N52 Neodynium magnets to be exact or whatever else you have lying around which is appropriate. ... Below is a link where I bought mine: ...
thingiverse
... are 10mm, which is a good fit for most of the plugs I have found. I'm using the Oceans Wonders coral frag plugs in the picture: https://www.amazon.com/gp/product/B06Y6DYQXW See also my corner-frag rack: https://www.thingiverse.com/thing:2672482
thingiverse
... Holes are 10mm, which is a good fit for most of the plugs I have found. I'm using the Oceans Wonders coral frag plugs in the picture: https://www.amazon.com/gp/product/B06Y6DYQXW See also my other frag rack: https://www.thingiverse.com/thing:2672511
thingiverse
These legs snap in at the holes of a eggcrate plate to lift the racks in your frag tank from the ground.
thingiverse
A small frag rack for my little 2 gallon fluval spec. I just wanted a small rack for my corals that wouldn't take up too much space in my tank. It has places for 5 little magnets from a Magnetix toy in the back which should be sufficient. I haven't...
cults3d
Frag rack capacity : 20 plugs you have to buy 4 suction cups 3 cm in diameter (amazon or others...) remove the thin layer of seaweed and fix the suction cups. ... 27*7*5 cm
thingiverse
Frag rack sections for saltwater tanks. Fusion 360 .F3D file is also attached. You use at least 2 Connecting Pieces to connect 2 sections of Egg Crate together. Connecting Pieces are probably going to be friction-fit depending on the Settings...
thingiverse
I needed a multi-level frag rack for my coral QT. I am using a WaterBox 10g cube but of course this could work in any tank. The bottom piece is meant to be used as a weight, I used eMarco cement as the weight material. Note you really can't use...