ft simple cub 3d models
268646 3d models found related to ft simple cub.myminifactory
This is a mock engine designed for the FT Simple Cub by FliteTest. Not 100% true to the real thing but has some nice detail and a flat bottom for easy mounting to the foam board. ...Checkout the full project writeup on my website!
thingiverse
Articulating - but not rudder controlled - tail wheel assembly for my FT Simple Cub. ... Link to my other mods: https://www.thingiverse.com/thing:3438487 and https://www.thingiverse.com/thing:3442863 and https://www.thingiverse.com/thing:2855083
thingiverse
This is for RC planes. ... This is made for the FT simple cub RC airplane.
thingiverse
This is an addition to my previously designed landing gear mount for the FT Simple Cub. it will help distribute the weight of the plane over a wider area and help to not tear the foam slots where the landing gear sets into the fuselage. Since hot...
thingiverse
I needed some larger wheels for my FT Simple Cub for some rough surface. All can be printed with no support. The Wheel is simple but functional. I printed the tire with 2 perimeters and 3 top and bottom layers. 3% infill to make it soft. ...
thingiverse
This is a basic strut/support for the FT Simple Cub's landing gear. The landing gear of the original tend to collapse after a few landings. This is a small support to prevent the foam at the base of the plane where the landing gear are attached...
thingiverse
Early 2019: This is V2 of my landing gear for the FT Simple Cub, based on the Timber gear, you'll need some 4mm bolts for the wheels, and optionally 3mm or 4mm bolts plus washers for the hinges, setting the wall thickness to 2mm will leave enough...
thingiverse
I didn't have good luck with the included landing gear mount for the FT Simple Cub, the gear tore the paper and foam on a rough landing so I designed this to be the same size as the foam piece. will need to open the slot a bit on each side at the...
thingiverse
... useful vent to keep the ESC cool without having large holes in the bottom of your craft. ...I recommend scaling it down, full size was too big for me. This is somewhat for decorative purposes, and isn't based on any actual details of the Piper Cub.
thingiverse
Here is the landing gear that is designed for FT simp[le cub to fit rc car shocks. If the shocks isn't stiff enough you might need a rubber band. All that is needed to complete one half the landing gear is the 3d printed parts with 3 pieces of 4mm...
thingiverse
Using as many parts as possible that come with the FT speed build kits.... 2.5mm rod, rubber bands and BBQ skewers. Weight is only slightly more than the foam and wire FT landing gear. Located in the same spot. ...Using a BBQ skewer to make it...
thingiverse
This is a gattling cannon for the Flitetest Simple Cub to make it look like Nick Rye's plane from Farcry 5
thingiverse
This is a motor mount for Flight Test foam RC planes
thingiverse
I just built a Simple Cub kit from Flite Test. The front windscreen was a pre-perforated hole for an FPV camera but I felt like it would be a bad idea to glue the camera directly to the windscreen. This is a plug for the hole while allows you to...
thingiverse
Design for the FT Simple Cub Rudder Might require splitting to fit on certain printers and is to be printed in half to allow for movement.
thingiverse
... side cylinders and air intake shrouds are each printed separately. Simply hot glue components to side of fuselage. The FT Simple Cub I believe is 1/10 scale, so if you want any other size, scale these replica motors in your slicer software.
thingiverse
Saw Hackoholic's design for the simple soarer and was blown away! ... What an elegant design to solve one of the problems I have been having with my FT planes. As promised here is one for the Cub... ... "No More Popsicle Sticks!!"
cults3d
Tail skid meant to fit the Flite Test Simple Cub Rough up the flat surface and stick it to the back of the plane right next to the rudder hinge. I've been dragging this on dirt and pavement for 20 or so takeoffs and landings and very little wear so...
thingiverse
Tail skid meant to fit the Flite Test Simple Cub Rough up the flat surface and stick it to the back of the plane right next to the rudder hinge. I've been dragging this on dirt and pavement for 20 or so takeoffs and landings and very little wear so...
thingiverse
Edit it online https://www.tinkercad.com/things/ite0WogTgBf A strut to replace the skewers in between the simple cub floats. Print with 1 or 2% infill to provide support to the cutouts, and it is recommended to add some support inside the cutouts as...
cults3d
Upgrade part for the Flite Test Simple Cub RC airplane When built to the plans the back of the wing that sits on the fuselage does not have a lot of support. The force that the rubber bands exert on the wing can fold the back part of the wing and...
thingiverse
Upgrade part for the Flite Test Simple Cub RC airplane When built to the plans the back of the wing that sits on the fuselage does not have a lot of support. The force that the rubber bands exert on the wing can fold the back part of the wing and...
thingiverse
Because at least three people asked how I did it, here are the files for the FT Cub I've modified. The wings are mounted on 4 points with two holes each. The wing mount fits snugly inside and is secured by anything that fits. I used bbq sticks,...
thingiverse
Flitetest FT Simple Firewall for FT Versa Wing Inspired by http://flitetest.com/articles/ft-versa-wing-build
thingiverse
... up off the surface while taxing, takeoffs, and landings. Overtime it will ware down a bit but can easily be replaced with just two screws. More detail over on my blog: https://backyardrc.wordpress.com/2015/05/13/piper-cub-rat-rod-project-update/