funjet ultra 3d models
9105 3d models found related to funjet ultra.thingiverse
This is my 3D Model of the motor mount from a Funjet Ultra. I did this model, because I needed different holes for mounting the new motor. There are two different sizes of mounts to choose from. The one you can see in the pictures is the short...
thingiverse
https://www.thingiverse.com/thing:4539843 FPV nose for Multiplex Funjet Ultra 2 designed to fit the Runcam Hybrid 4K camera. This nose also fit the regular funjet 2 and the old funjet and funjet ultra! Cutting the nose off a funjet straight is not...
thingiverse
https://www.thingiverse.com/thing:4539843 Low drag FPV nose for Multiplex Funjet Ultra 2 designed to fit the Runcam Micro Eagle FPV camera. This nose also fit the regular funjet 2 and the old funjet and funjet ultra! Cutting the nose off a funjet...
thingiverse
Low drag FPV nose for Multiplex Funjet Ultra 2 designed to fit the Runcam Phoenix 2 FPV camera with 2.1mm lens. This nose also fit the regular funjet 2 and the old funjet and funjet ultra! Cutting the nose off a funjet straight is not an easy task...
thingiverse
Piezas para el montaje FPV, soporte cámara FPV, requiere un pequeño corte del corcho para encajar el soporte, soporte de Vtx pegado en la tapa superior y atornillado para que la refrigeración sea buena, el mismo soporte del Vtx hace de cierre de la...
thingiverse
This cover is slightly higher and wider so that the servo horn does not grind
thingiverse
Printed with 0,20 layer high. ... matching servo: feetech ft90m 270
thingiverse
This nose also fit the regular funjet 2 and the old funjet and funjet ultra! Cutting the nose off a funjet straight is not an easy task but I came up with a method for it and it worked out great, after the failed atempt with the black marker. First...
thingiverse
Low drag FPV nose for Multiplex Funjet Ultra 2 designed to fit Foxeer mini cameras with 1.8mm lenses such as falkor, predator 1 to 4, monster and razer. This nose also fit the regular funjet 2 and the old funjet and funjet ultra! Cutting the nose...
thingiverse
Simple Tray to house all the electronics for a Funjet 2 with FC setup. The tray clips strongly under the carbon spar and is removable anytime. Make sure the ESC wires are long enough to reach when replacing motors ore removing the tray. Keep in...
thingiverse
fit a NTM Prop-Drive 28-36 3000KV Print with PETG or ABS
thingiverse
A wall mount for funjet 2 and funjet 2 ultra. You need 2-4 M3 screws (or wood screws) for the front or just glue it together. The funjet sits quite stable without the front, but I wouldn't risk it. ... Hole spacing in the back is 60mm.
thingiverse
Designed for the funjet 2 ultra when using 25mm diameter five hole pattern 4-pole car/boat motors. Specificly designed for the surpass hobby 3660/3670 series with vents. use 40x3mm aluminium for the hybrid version, bottom hole is smaller and should...
thingiverse
Funjet motor mount for improve the aerodinamic performance, mainly for the propeller. - Improves propeller performance by receiving more clean air. - Venturi effect to better extract inside air - Less propeller noise, so more performance. ...
thingiverse
A little spinner for the funjet 2 vector motor. ...you can press fit or glue the nut in.
thingiverse
Simple Design, should fit well in the FunJet Battery holder cutout. ... Let me know if you print it and try out.
thingiverse
For a lightweight version of the Funjet, I designed this mounting. ... The motor mount is for a small 1402 motor with 12mm hole spacing.
thingiverse
Funjet Nose Cutting template for Henrik Jäderström absolutely great Funjet Nose - Thank you Hendrik !! Before you cut off the nose, test that the template fits flush to the end (adhesive surface) of the nose, that must fit 100% !! Otherwise, make...
thingiverse
This is an FPV mount for a Multiplex Funjet - http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXZWK8 It was designed in Google Sketch up by a friend and printed on an UP! Mini. The orientation of this part is important when printing to reduce the...
thingiverse
So after a serious crash, which distroyed the complete front of my funjet, I thought about to convert this thing to a front driven plane. Now, as a proud owner of a new Ender 3 V2 3d printer, I used fusion 360 to create my first own 3D...
thingiverse
... flat areas for less drag and better/more airflow. The wide version also matches the curvature of the fuselage better than the old version. made to fit 50mm to 65mm diameter circular fuselage. Fits all funjet versions and probebly most clones too.
thingiverse
The motor mount: I modified the original 3DLabPrint mount so it can take the stock motor mount that the Multiplex Funjet uses, which made it much easier for me to mount my 28mm inrunner motor. Mount Formers: This helps to keep the motor...
thingiverse
Made this motormount for Multiplex microjet. ment for a 28mm outrunner inside.. bolthole is 13x13mm. It`s hard to get the motor inside, use the force!!! Use long wiers on the motor.. cut in to the foam for good fit. V2 motormount is the blue...