furious fpv 3d models

Furious FPV AcroWhoop V2 Mount This mount fits the new Furious AcroWhoop V2. It holds the FPV Camera at 10 degrees. Design to print in Semi-Flexible TPU and screw/glue into the front mount of the board. Camera secures with a rubber band around a...

Furious FPV 2.4 vtx mount takes two 3x6mm bolts to hold it in.

These things are mounts for the Furious FPV Stealth Race VTX and the the Stealth Long Range VTX, both with bluetooth modules. ... You can use these mounts for every other stack with the same mounting hole distance.

Wanted my Furious FPV cable to be held behind me on the strap. Found something close but modified to fit the smaller cable and add a semi-closure to the bottom of the clip. ...Print 3 or 4.

Simple ground station mount for the Furious FPV Dock-King. ...It allows to put one battery (with a strap) on the side and one smart case on the other side, while the back holds a monitor (here the screen from the Eachine EV800).

Furious FPV 5cm Pigtail support for patch antenna.

This is a receiver cover for the Furious FPV True-D receiver for the Flysight FG01 FPV goggles.

While I don't like furious because they fucked me hard support-wise, I have to admit they have nice products. I love that lil Moskito 70 fucker and made a battery mount so that there is no need to fiddle with rubber rings anymore. This mount snaps...

This design is made to match for the most part the original protectors of furiousfpv's moskito 70 (one of the smallest brushless fpv quad). It weights about 6g according to Cura, roughly the same as the original one. True printed protector weight its...

... fpv. ...Il est imprimé en TPU (ninjatek) pour protéger le contrôleur de vol contre les vibrations et les chocs. Magasin UE: https://www.drone-fpv-racer.com/piko-blx-micro-flight-controler-furious-fpv-980.html Https://www.facebook.com/Microdure/

Furious Fpv FylingFrog Frogshoe by mg_EARL This is a snap on motor and arm protector. I usually use PLA. It might explode during a hard crash on concrete, but it protects the motor and the arm tip properly. ... Infill: as you prefer, I use around 40-50%

Here is a custom 30.5mmx30.5mm adapter for Furious FPV-0121-S FRSKY . It is printed in TPU ultimaker 95A (ninjatek) to protect the receiver from vibration and shock. ...A version with and without buzzer Mini receiver furious: Store...

Here is a custom 30.5mmx30.5mm adapter for Furious FPV-0121-S FrSky. It is printed in TPU Ultimaker 95A (ninjatek) to protect the receiver from vibration and shock. A version with and without buzzer Mini receiver furious: Store...

VOICI ONU personnalisé 30.5mmx30.5mm adaptateur Verser Furious FPV-0121-S FrSky. Il est imprimé en TPU Ultimaker 95A (ninjatek) Verser Proteger Le Récepteur Contre les vibrations Et Les chocs. Une version avec Et Sans buzzer Mini récepteur furieux:...

Furious FPV GPS Mount for Martian II Frame. There are two version : - Version with 2 mm space if you want to put a M3 adhesive under the mount like I did (see the picture) - Flat that is directly on the Frame The module wont be ejected as...

Furious FPV True D V2 replacement cover. Since the old Cover was big and clunky, I decided to make my own. This is what I came up with, a simple and space saving solution. It is a very snug fit, so don't take it out and put it back in that often.

Here is a custom 30.5mmx30.5mm adapter for Furious FPV-0121-S FRSKY . It is printed in TPU ultimaker 95A (ninjatek) to protect the receiver from vibration and shock. ...A version with and without buzzer Mini receiver furious: Store...

Just print in Ninjaflex or TPU at 30/40% infill ;)

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fpHkvusjimh

I got sick of my Fatshark Module's antennas flopping around. I leave the adapters on permanently, and this little dingus slips over them to keep them straight. I used a blob of rubber cement to keep them on. Works great, but you won't be able to...

Hi, this is Remix from @robthomson 's Rapid Fire / Dock King Cover. This one is made to work with Eachine PRO58 receiver. ...

Remixed to accommodate larger battery (300mAh). ... Tub is 10mm deep by 16mm wide.

Petite cale pour maintenir le VTX au dessus de la stack pour le laisser libre

... from Furious fpv. ...It is printed in TPU (ninjatek) to protect the flight controller from vibration and shock. Store EU:https://www.drone-fpv-racer.com/piko-blx-micro-flight-controler-furious-fpv-980.html https://www.facebook.com/Microdure/

... from Furious fpv. ...It is printed in TPU (ninjatek) to protect the flight controller from vibration and shock. EU Store:https://www.drone-fpv-racer.com/piko-blx-micro-flight-controler-furious-fpv-980.html https://www.facebook.com/Microdure /

Store EU:https://www.drone-fpv-racer.com/piko-blx-micro-flight-controler-furious-fpv-980.html https://www.facebook.com/Microdure/ Print Settings Printer Brand: Ultimaker Printer: Ultimaker Original Rafts: No Supports: No Resolution: 0.10 Infill: 100%...

This is a design for a flexible housing or cover that protects the Furious FPV V3 module when used in the Fatshark Attitude V3 FPV Goggles. It offers some impact and weather protection over running the module uncovered and adds some strain relief for...

WORKS: Rapidfire, Clearview, Furious FPV, Nextwave RC. Dimensions 52mm (width) x 35mm (height) x 36 mm (depth) Simple box-style module holder and protector for Fatshark goggle modules. Allows you to carry along backups or alternatives (eg, for...

I got tired of batteries being ejected in crashes making the beeper useless for recovery when using other battery mounts on Thingiverse so I designed a combined ESC cover and battery holder. It uses the same mounting holes and screws that comes...

This is a very simple replacement clip for the ones which hold the True 3D diversity unit into the injected molded case.