garden hose valve replacement 3d models
198065 3d models found related to garden hose valve replacement.thingiverse
The handle on my garden hose valve broke. So, I measured it, designed a handle on Fusion 360, and printed it out on my Wanhao I3 Plus printer. It came out pretty good. I printed in PLA at .15 layer height and it needs no supports. It's a tight...
thingiverse
I made this from scratch as a replacement lever for my garden hose splitter after it broke off. The measurements are pretty precise. I printed in 0.1 mm layer height for the detail, with supports just for the screw hole. If you have this part, you...
thingiverse
This was created to solve the problem of the lever arm being too small and never knowing which way to turn the valve off. The OFF nomenclature is on both sides. Arrow is cut through. If your valve closes the other way for some odd reason, flip the...
thingiverse
I printed the Garden Hose Valve Helper to give leverage to operate the valve on a Y adapter, but due to the orientation of the handle, it knocked against the hose spigot. Also, the valve on each side of the Y operates in the opposite direction, so...
thingiverse
I got a complaint that the stock metal valve handle was too hard to turn because of the small ridges, so I made this one with a bit more leverage (much longer ridges) and only three bumps (instead of the usual six small bumps). ...It seems to do the...
youmagine
I got a complaint that the stock metal valve handle was too hard to turn because of the small ridges, so I made this one with a bit more leverage (much longer ridges) and only three bumps (instead of the usual six small bumps). It seems to do the...
thingiverse
Replaces my lost washer that holds the release value together for my garden sprayer. OD 8.5mm ID 3.5mm The little plastic washer was lost by a loved one while using the sprayer unsupervised. lol 30 minutes later (5 minutes measuring, 15 minutes...
pinshape
Summary Replaces my lost washer that holds the release value together for my garden sprayer. OD 8.5mm ID 3.5mm The little plastic washer was lost by a loved one while using the sprayer unsupervised. lol 30 minutes later (5 minutes measuring, 15...
cgtrader
Garden hose ball valve 3d model. ...Polycount: nosub - polys 13086 verts 13221 1 sub - polys 104688 verts 52609
thingiverse
This is a replacement ON/OFF 3/4” ball valve operator for the Vita Guardian 75 foot expandable garden hose. The original operator included with the hose fell off and was lost within days of purchasing the hose :( This replacement is a perfect fit. ...
thingiverse
It seemed odd that no one at all makes mounts for the garden hose valves you find at your local home improvement or hardware store. The inexpensive valves (*like the one I used*) work well enough but there is no way to mount them. Some variants have...
thingiverse
I think it fits fairly well by itself, but if you want you can also buy a longer screw and replace the screw in the faucet with the longer screw to make sure it stays in place. You'll need a, #4 x 3/4-in Machine Screws. It touches each other a bit,...
cults3d
I got a complaint that the stock metal valve handle was too hard to turn because of the small ridges, so I made this one with a bit more leverage (much longer ridges) and only three bumps (instead of the usual six small bumps). ...It seems to do the...
thingiverse
My mother has pretty advanced arthritis, but also loves to garden. Unfortunately our water tap has a tiny hard to open lever on it(pictured ). I'm a total amateur, but I designed a simple handle to make it easier, and it's worked amazingly well. ... ...
thingiverse
Male hose connector for Melnor quick connect 237-337.
prusaprinters
The super glue is required to get the part air tight.Once the glue has set insert it fully into a garden hose (something like Gardena Classic, 13mm or ½"), and fix it with a hose clamp.Pressure limits are 6 bar with a Dunlop valve, or 10 bar with a...
thingiverse
... as an endpoint for my hose connector. This replacement lid has a cutout for a garden hose to pass into the valve box. ... Should fit Rain Bird VBA02672 note: only suitable for low traffic area's as it lacks the "snap tabs" of the original.
prusaprinters
<p>Printed with 0.2mm layers using ABS</p><p>Print on the side with supports enabled.</p><p> </p>
cults3d
A replacement knob/grip the pressure release valve on a filling hose for a Bauer compressor. there are two parts to this the hex ring that interfaces with the brass hex part of the release valve and the grip itself. the hex ring and the grip should...
thingiverse
Replacement bleed valve for Nilfisk P20 vacuum cleaner hose. These have a tendency of falling off, and replacement parts are not available AFAIK. For good seal, it is important that the inside is as smooth as possible. For strength, this thing...
prusaprinters
A replacement knob/grip the pressure release valve on a filling hose for a Bauer compressor. there are two parts to this the hex ring that interfaces with the brass hex part of the release valve and the grip itself. the hex ring and the grip should...
grabcad
This CAD file is a model of a Garden Valve. ...And this garden valve is been used in various applications. ...This is a zip folder comprising a password, and if you require the password please make a 'Like' and make a request to me.
youmagine
The little plastic washer was lost by a loved one while using the sprayer unsupervised. lol 30 minutes later (5 minutes measuring, 15 minutes tinkercad, 10 minuters printing) and all is right in the spraying-things-world again. ...PLA 0.2mm Layer ...
cults3d
In the case of using PLA the following parameters are recommended: *Extruder temperature: 195°C *Bed temperature: 60 °C *Filling / infill: 60% *Apply the function supports and fixation on CURA Holder for garden hoses, towels or other objects with...
thingiverse
Does your garden hose valve match the image? ...Maybe this is a workable valve handle for you, My print *just* clips on.