gen 8 gearbox 3d models
350265 3d models found related to gen 8 gearbox.grabcad
FRC Gearbox 8:1-3 Falcon motor-1/2 in hex shaftThis is not an applicable gearbox. It may be defective in structure and has never been verified by assembly. ...Just a try and for fun :)
thingiverse
Building and Testing Video: https://youtu.be/IHZo5n1dCxE Bearings: https://ali.ski/y1YkQ 12V DC motors: https://ali.ski/zKwdh Gearbox and water pump they are not new things in this channel, but I was thinking to make the best, most powerful and...
thingiverse
Just a basic stand I made up for storage of my redcat gen 8 to take the weight of the rc off the wheels to prevent flat spots. It also works great for working on it when the wheels are off. ...Will need to print two stands, they are interchangeable from...
thingiverse
This is my bullpup m4 conversion designed to fit the standard gen 8 gelball blaster receiver. it requires only small modifications to the receiver to fit though a longer front guard such as i did is suggested. ... You will need m3 and m4 screws and...
thingiverse
Gearbox for 8,5x20 motor 1.9:1 ratio. 2mm shaft (I use titanium for low weight). ... Pulling > 3 amp(raw gear and bearings) with turnigy 3x2 propeller, after breakin 2.5 amp https://www.youtube.com/watch?v=sHD8Hc-Hy8Y
grabcad
The scope was to design an 8:1 speed reducer gearbox for industrial machines based on a set of requirements. ...My final design has the following specifications:*Total Mass: 24.89 kg*Input Shaft/Layshaft Speed Ratio: 4:1*Layshaft/Output Shaft Speed...
thingiverse
Made for the light buckets and bumpers on the Redcat Gen 8. ...Uses 2mm screws.
thingiverse
Redcat Gen 8 Beadlock (wider) Ring, aligns and works well with all 6 screws.
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Gas Cap V1.STL) + (Gen 8 Gas Cap V2.STL) + (Gen 8 Gas Cap Base.STL) + (Gen 8 Gas Cap Spacer.STL) for others, you may not receive compensation in excess of...
thingiverse
Redcat Gen 8 roof rack. Not the best but works, Used M2*8 and M2*20 hardware. The leds I used came with some Special clips that gets held in by a 15/64 hole on the light bar mount. ...Also use some countersunk screws on the lightbar to keep the roof...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Door Handle L.STL) + (Gen 8 Door Handle R.STL) + (Gen 8 Door Handle Spacer.STL) for others, you may not receive compensation in excess of $0.15 per part,...
thingiverse
Redcat gen 8 servo relocation mount. This part eliminates most of the stock body roll and helps with bump steer. You have to move the drag link to the knuckle. See first photo Setup shown is a savox 1258 servo and an RC4WD 25T motor. Plenty of...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Accessory Plate For Fan.STL) or (Gen 8 Accessory Plate Solid.STL) for others, you may not receive compensation in excess of $1.50 per part, plus your...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Tailgate Grill.STL) for others, you may not receive compensation in excess of $1.50 per part, plus your shipping costs. ...This number is calculated based on an...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Liftgate Button.STL) + (Gen 8 Liftgate Button Spacer.STL) for others, you may not receive compensation in excess of $0.15 per part, plus your shipping costs....
pinshape
All three pieces bolt together, and are sized to fit the Gen 8 Scout perfectly. Just drill a few 2mm holes in your body after you chop the top and your good to go. ...Fair warning, this will take a long time to print as is, i made it so it would be both...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Windshield Wiper.STL) for others, you may not receive compensation in excess of $0.15 per part, plus your shipping costs. ...This number is calculated based on...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Grill V5.STL) for others, you may not receive compensation in excess of $1.75 per part, plus your shipping costs. ...This number is calculated based on an...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Grill V2.STL) for others, you may not receive compensation in excess of $2.25 per part, plus your shipping costs. ...This number is calculated based on an...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Roof Rack.STL) for others, you may not receive compensation in excess of $1.50 per part, plus your shipping costs. ...This number is calculated based on an...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Grill V4.STL) for others, you may not receive compensation in excess of $2.25 per part, plus your shipping costs. ...This number is calculated based on an...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Grill V3.STL) for others, you may not receive compensation in excess of $2.00 per part, plus your shipping costs. ...This number is calculated based on an...
thingiverse
I designed these to replace the standard body mount used to mount a normal poly body onto the Gen 8 chassis. They are made to fit rare earth magnets from harbor freight https://www.harborfreight.com/10-piece-rare-earth-magnets-67488.html ...
thingiverse
Children electric car gearbox. ...54-8 gears 4mm hole
cults3d
4-stage cycloidal gearbox with a reduction ratio of 1/8.5 mil. Driven by an eccentric of 0.86 mm. Reduction by the housing with 55 journals and 4 shaft gears with 54 shafts each. To test the gear reduction, the gearbox was coupled with an...