gep rc 3d models

This is a simple low prifile gopro session mount I made for the Gep-rc vx5. ...Enjoy!

Just digitalize my GepRC Leopard frame in Fusion 360.GEP-LX5” 220mm frameIt does not have 100% of the details(some holes missing), but it's 100% accurate.Nice and strong frame. I am going to create aerodynamic​ 3d printed housing. ...Update model soon.

Arm Protector for GEP RC Mark 1 Frame.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Print in TPU. ... It's a little rough, but it works

Funny horns for lipo containing

This is an universal GoPro mount for your GEPRC KHX5 elegant. I printed it in extrudr flex hard. ...Any kind of flexible should work, though.

used PLA plast

case to foxeer box 2 + tracker rf v16 to GEP RC drone to a best resoults print it from tpu .

Geprc Ngp 8 universal mount with SMO Grip

Session 5 mount will be added soon Print instructionsUnassociated tags: BOX 2, GEP RC, MARK 4, SESSION 5 Category: R/C Vehicles

GEP-KHX5

“The GEP Gun is the most silent way to eliminate Manderley” My attempt to remake GEP Gun from Deus ex

some of the gep LX5 come with 4 of same arms if yours is like that print the left and right and if right fits all of them use right same for left. ...mine came with 4 arms but 2 where mirror images of other so i made left and right guards left fits arm...

xt60 mount in 2 strengths for the gep-ax4

Another remake of legendary GEP gun from Deus ex(2000 Ion Storm)

Created with http://www.instamuseum.com Original photos at https://www.instagram.com/gep.gepgep

VTX holder for the GEP LX5. This unit mounts by clipping into the two slots on the aluminum part of the frame (no screws needed). Designed in Freecad. ...

Simple little mount for a 12mm buzzer on a GEP-LX5 frame. This will raise the canopy up 2mm. I use a capacitor holder on the front of the quad to lift the front 2mm. ...

This riser is designed to provide 3mm additional space between the metal sides and the carbon frame of your GEP sparrow quadcopter. ... Print 4 of these in PLA and you'll have a bit more room for a taller stack.

Canopy for the GEPRC GEP-TX5 Chimp, including mount for a XT60 connector at the back. I broke off the aluminium stands on my original frame and didn't want to wait for new parts, so I drew up this canopy. Printed it in TPE, feels like it should...

Canopy for the GEPRC GEP-TX5 Chimp, including mount for a XT60 connector at the back. I broke off the aluminium stands on my original frame and didn't want to wait for new parts, so I drew up this canopy. Printed it in TPE, feels like it should hold...

This is a pod for the GEPRC GEP-TX Chimp. I did not print it because I have no printer. But for the info I have, this print must fit. Fc and pdb position is 3mm spacers under the pdb and 10mm between pdb and fc. You have than enough space for the...

Motor oder Arm Schutz für einen GEP-MX3 Frame.

This is a universal camera mount for the GEPRC GEP-VX5

Made for the GEP HX2 and the VTX03. ...Do it in TPU.

GEPRC GEP-KX5 ElegantHolybro Kakute F7 FilghtcontrolHolybro Tekko32 35AArduino Leonardo Micro for RSSI from Multiplex RX7 ReceiverEachine 1000TVLRunCam DVRTrump HV

This is a GPS holder for GEPRC GEP-VX5 Drone Frame printed in PETG Nozz: 240 Bed: 70

Antenna holder for the gep-mx3 frame. It works perfectly for mmcx antennas. ... If someone wonders, I'm using the DJI air unit antennas (LHCP).

For GEPRC GEP-TX5 CHIMP Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Resolution: 0.2 Infill: 50