geprc phantom 3d models
4859 3d models found related to geprc phantom.thingiverse
simple buzzer mount for GepRC Phantom. to be installed on the rear stand-off. printed in TPU. The two wires on each sides. ... enjoy.
thingiverse
Bumper for "Geprc PHANTOM" to be installed through the use of a clamp. ...By tightening the clamp, the bumper moves slightly away from the body, this allows you to absorb even better the blows coming from the bottom and from the side.
thingiverse
I crash my GEPRC Phantom every once in a while and I had an extended wait to get a replacement bottom plate, so I took matters into my own hands and scanned myself a new one! I reinforced the arms slightly to make them more rigid and I enlarged...
thingiverse
GEPRC Phantom Minimortal Antenna Mount I could not find an STLs for the original parts so I made this. ... Vista mount is here: https://www.thingiverse.com/thing:4682809 UPDATED: Removed a little bit more material for weight saving.
thingiverse
GEPRC Phantom Vista Antenna Mount Could not find any STLs for the stock parts so I made this. It has an XT30 holder as well which the stock print did not have. ... The Minimortal mount is here: https://www.thingiverse.com/thing:4682847 UPDATED:...
thingiverse
GEPRC Phantom lollipop antenna and rx mount.
thingiverse
Remix of this DJI camera holder for GepRc Phantom frame https://www.thingiverse.com/thing:4552853
thingiverse
Camera Mount For RunCam Thumb!! ... I use this on GepRC Phantom Frame.
thingiverse
geprc phantom frame with crazybee F4 V3 board, 1103 brushless, 2.5" avan blur prop, 3S, DJI caddx vista
thingiverse
Modified the stock Runcam Thumb Pro mount that it ships with to suit the GepRC Phantom frame. ...Use an m2 screw and nut for the rear mounting point.
thingiverse
GepRC Phantom HD Caddx Pro Mount I replaced the stock Caddx Nebula (60fps) with a Caddx Pro (120fps) so here is the quick mount. ... Print (2) pieces mirrored.
thingiverse
This part is a plate that lets you mount a Insta 360 Go to the rear of a GePrc Phantom quadcopter. CAUTION: Mounting the camera will impact the center of gravity and will wear out the rear motors. Try at your own risk! ... Read more about the...
thingiverse
Geprc Phantom crossfire antenna holder, not a perfect L, but its pretty close and I assume will work good enough for a toothpick of this size and weight, not built for long range. ...The other tpu 3d print parts are on thingiverse from other creators.
thingiverse
Fits the old GEPRC Phantom HD 3inch frame. Made the base a little sturdier to remove vibrations. All credit goes to B0bafart for the awesome mount and lens cover. ...If you want the cover, go check him out and give him a like
thingiverse
Needed a stronger case and mount for my geprc phantom hd and gorpo lite so i could freestyle it without worrying about trashing my naked gopro so i took the strongest case i know and made it lite! ...i used tpu to print.
thingiverse
GEPRC Phantom Toothpick FPV camera mount It is TPU mount but more durable than the carbon fiber that comes with the frame. The carbon fiber holder broke easily after few flights so I decided to design this TPU light weight holder about 1.2 grams...
prusaprinters
GEPRC Phantom Toothpick FPV camera mount It is TPU mount but more durable than the carbon fiber that comes with the frame. The carbon fiber holder broke easily after few flights so I decided to design this TPU light weight holder about 1.2 grams but...
thingiverse
Designed this so i could put the runcam phoenix on The Phantom for less latency and more res
thingiverse
This is a remix of https://www.thingiverse.com/thing:4431014 I needed skids added so the bolts on the bottom of the frame would not scrape.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/1goK0aYwMvY
thingiverse
This is a antennas mount for a GEPRC Phantom and a Foxeer Lollipop 3 antenna
thingiverse
GEPRC Phantom/Smart 25 2.4G Hinge Mount. ... This is based off of the excellent Haku3D designs - https://www.thingiverse.com/thing:4882912
thingiverse
Quick and easy mount for the Phantom HD. Made a tab to slide into the frame for some extra support of the camera. Fits snug on the camera and bolts directly to the frame. Can print with or without supports. ...Leaves some stringing without supports...
thingiverse
The first part was the Geprc Phantom Crossfire "L" Antenna holder by MTopp on August 29, 2020, https://www.thingiverse.com/thing:4582717 The second was the GEPRC Phantom XT30 by RobertS71 September 06, 2019, https://www.thingiverse.com/thing:3847623...
thingiverse
I exchanged the mediocre Caddx EOS on my GepRC Phantom with the Caddx Turtle V2 whoop edition. The camera is a perfect replacement and fits nicely. The board can be mounted below the bottom frame. I just needed a cover/holder that would protect the...