harbor freight 3 ton jack 3d models

Roughly based from Harbor freight 3 ton jackstand (pittsburgh brand)Around +/-1/8" accuracyhttps://www.harborfreight.com/3-ton-steel-jack-stands-61196.html

This is a handle to use with on the release valve on the Harbor Freight "T-style" 6-ton bottle jack press. ...It's a very snug fit.

These can be printed to hold the jack handle on the press frame. I recommend double sided tape to hold them on or using the holes for screws. ... PLA / PETG whatever print around 40% infill it does not need to be strong

Remix of hgglmmr's Mercedes Benz jack adapter for Harbor Freight 1.5 ton aluminum racing jack. ... Printed in ABS at 100% infill for strength.

Remix of hgglmmr's Mercedes Benz jack adapter for Harbor Freight 1.5 ton aluminum racing jack. ... Printed in ABS at 100% infill for strength.

Made this to use on the harbor freight 6 ton hydraulic press. HUGE improvement over using the handle to release pressure. ... It's a very tight fit.

Made a quick remix to Fit the smaller 12 ton Harbor Freight Press. Not Perfect but snug fit for Handle. ...Thanks for Deifox for making the orignal

a place to store your Harbor Freight 12 ton press handle when not in use.. ...Lock two of these onto the top I beam and lay handle in U shape..

This is a jack handle keeper for use with the farm jack available at Harbor Freight(see photos). My jack is mounted on my Jeep and this piece keeps the handle from rattling around. ...Print using Ninjaflex filament.

This knob allows you to easily open and close the valve on the Harbor Freight 12-Ton Press hydraulic cylinder, instead of using the handle to do it. ...It accepts a #10 x 24 tpi hex grub screw to secure the knob to the valve shaft.

Created a 12 ton hydraulic bottle jack pressure release valve. I'm not great at CAD, but was able to create this with a little effort. ... Works great!

I wanted a handle holder for my 20 ton press for ease of use, so I came up with this design. I made this out of ABS and it's a pretty tight snap fit. ...You can try different material if you like, but this probably needs to be ABS or nylon for the...

I wanted a handle holder for my 20 ton press for ease of use, so I came up with this design. I made this out of ABS and it's a pretty tight snap fit. ...You can try different material if you like, but this probably needs to be ABS or nylon for the...

A simple knob for the HF 20ton air over hydraulic bottle jack. It is a tight press fit (I used a small hammer. I guess it would be ok to epoxy it in or drill though for a pin. I am very much a newbie on this. I am glad to help if I can. ...

Replacement cap for the el-cheapo Harbor Freight Trailer Tongue Jack. The original didn't fit snugly and fell off on the road somewhere. This is long enough to drive a set screw into from the outside, but at least on mine it fits snugly enough not to...

... insert which are 6.3mm wide. ...I also included a bevel on only one side to cleat the jack parts. This is the jack I am using: https://www.harborfreight.com/3-ton-low-profile-super-duty-floor-jack-with-rapid-pump-candy-apple-metallic-red-57589.html

Harbor Freight 12 Ton Press has tolerances too loose for pushing a pin out with a punch. ...Adding one of these to each side of the press will prevent side-to-side shifting of the press.

Harbor Freight 12 Ton Press has tolerances too loose for pushing a pin out with a punch. ...Adding one of these to each side of the press will prevent side-to-side shifting of the press.

This knob is to prevent you skinning your fingers when using the harbor freight 1 ton engine hoist, which has the most terrible hydraulic valve "knob" (a metal shaft). It is impossible to get good control with the built in method and easy to skin...

4-pin trailer plug holder for my Harbor Freight trailer that mounts to the jack also from Harbor Freight. If mounted like in my picture, it clears the jack crank without any issues. I used the plug holder from:...

3 Long bin for harbor freight parts storage, good size for keeping a screwdriver in the same storage container as the hardware.

This is inspired by the need to organize little things. ... I took DIY3DTECH's divider and made a long way divider for 3 long bins. This is for the Harbor Freight medium storage bin large box.

These are a softer version of the very sharp metal jaws that come in the Harbor Freight 3" bench vise. ...They are easy to swap out when you need a softer clamping surface and can easily be sacrificial if need be, just print another set.

This is my first design. ...Just a simple work light holder for a quantum magnetic work light from Harbor Freight. ...It works really well surprisingly!

This is a holder for the 3/8 Allen sockets sold at Harbor Freight. It has 6 slots for 4, 5, 6, 7, 8 and 10mm sockets and the option to add a 12x3mm magnet at the bottom for additional securement. ...I have found that I didn't need the magnet, as it's a...

I made a minor tweak to the model to fit my Harbor Freight vise sku number 61329, 7421. ...These soft jaws will work great for not marring projects in the device.

3 Long bin for harbor freight parts storage, good size for keeping a screwdriver in the same storage container as the hardware. Print Settings Printer Brand: Prusa Printer: i3 MK2SRafts: No Supports: YesResolution: .2 Infill: 20% Category:...

I modified SteelTallon's tool caddy to hold my 6" Harbor Freight caliper. I also widened the mount to eliminate the wobble where it sits on the spool bracket. Another user confirmed this also fits the similar looking model of CenTech calipers. ... If...

I have several of the freebie LED lights from Harbor Freight lying around (https://www.harborfreight.com/2-piece-3-12-in-led-mini-flashlight-63600.html), so I thought I could make up a clip that would hold the light at the top of my Ender 3. The...