hc 06 3d models
21311 3d models found related to hc 06.grabcad
That is my first project. ...That is Bluetooth HC-06. I hope to be usefull for someone. ...The sizes on lenght, width, height is 100% true, but position and size on elements is + or - 10% from sizes and positions.
thingiverse
From one photo you can see my latest cable harness for connecting both Micro Minim OSD and HC-06 in parallel to my Pixhawk Mini Telem port. To not overload the Pixhawk power supply I added an additional 5V power cable which goes directly to the...
thingiverse
I designed a Bluetooth module holder ( HC 06) to use it with my 3D printer ( a modified Ultimaker Original ) . I had to design both the Bluetooth and the holder to in the CAD software to check compatibility and clearness . The BT module is...
thingiverse
_Spanish:_ Carcaza para el módulo Bluetooth HC-06. El conector es del tipo 6P4C con pines para soldar en PCB. Ver circuito en <a href="http://www.freesensors.com.ar/index.php/hardware/sensores/8-modules/22-bluetooth">FreeSensors</a> . La carcaza...
thingiverse
Every time I wanted to flash the firmware on an HC-05 / HC-06 I ended up soldering temporary wires to the SPI Pads and once I'd finished programming, removing them. Thankfully now I don't have to! This holder gives you access to the 4 SPI pins along...
thingiverse
This is a Base to hold the Arduino Nano shield, A HC-06 or 05 Bluetooth and a 4CH relay so you can control 4 things from a smart phone. ... Will update photos soon
thingiverse
Just apply a bit of glue and under your HC bluetooth module and screw the holder in place.
thingiverse
Holder and cover for HC-06 or HC-05 BT module to fit 2020 Frame but can be put anywhere. The cover is just an extra touch if done in a translucent filament you can see the sync light. ...Print Settings Printer Brand: RepRap ...
prusaprinters
A re-mix of "Bluetooth Module JY-MCU" by cmspooner https://www.thingiverse.com/thing:254544/filesI needed a model of the HC-05 module that sits on top of the JY-MUC pcb.Also check out...
thingiverse
【HC-05/HC-06 Bluetooth Module Simple Bracket】 ArduinoやRaspberry Piなどのマイコンボードでよく使われるBluetoothモジュールHC-05やHC-06を製作物に固定するためのシンプルなブラケットとなります。 ワイヤー脱落等による信号が途切れるのを防ぎます。 固定用のビス穴はM3サイズの2点、15mm間隔となっています。 【Google Translation】 It is a simple...
thingiverse
Housing for HC-06 4 pins bluetooth module. Status LED is different ! ...Print Settings Printer: Uwe´s DIY Rafts: No ...
thingiverse
Caja diseñada para soldar una extensión de antena al bluetooth y protegerla con un tubo de plástico de 3mm. Soldando una antena de 2.4 estandar de cualquier RX al modulo hc06 ganamos mas distancia de emisión y recepción, ideal para Chorus Laptimer. ... ...
thingiverse
Zumo arduino bracket with onboard bracket for bluetooth module HC05
cgtrader
HC series Bluetooth module & board HC-06 bluetooth module - Dimension : 26.9mm x 13mm x 2.2mm bluetooth module board - Dimension : 1.52* 3.57cm
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: slitlength = 12 fontsize = 8 line_spacing = 2 line_10 = text_style = -80 letter_spacing = 1 slitwidth = 4 corner_radius = 3 plate_thickness = 3...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Loop_x_position = 11 Text = #HC Loop_font = Chewy height = [5,6,4,5,4,3,5,4,6] Loop_character = o center = 60 Loop_y_position = -10 twist = -3...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: line_10 = letter_spacing = 1 line_spacing = 2 slitwidth = 4 corner_radius = 3 font = write/orbitron.dxf text_style = -80 slitlength = 12 fontsize...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options: image_file = lithopane_new20150906-12423-8v4bwg-0.dat layer_height = 0.1 number_of_layers = 15 text_line_5 = text_line_4 = text_line_3 = HC?
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2041273 Instructions Using the following options: back3 = testbot back2 = UM PLA back1 = UM2+ left3 = Cura 2.3.1 left2 = 40 mm/s left1 = 5 mlt right3 = 18% infill right2 = 70 flow right1 = 1.2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1333056 Instructions Using the following options: Pin_Leg = 0.75 CHIP_Width = 13 PAD_WIDTH = 1 Stud_Depth = 0 Chip_Margin = 0.2 Base_thickness = 2 Chip_Height = 27 Pin_body = 2.6 Offset1_Y = 0...