honda crv phone holder 3d models
373684 3d models found related to honda crv phone holder.
thingiverse
This is a cell phone holder for a Samsung Note 8 and a 2020 Honda CRV EX-L. With a phone in the holder it does block the hazard light switch but removing the phone gives you access to the switch. It also allows air from the vents to get to the phone...
thingiverse
This is a mobile phone holder designed specifically to fit into the Honda CRV cup holders. It includes holes for threading a USB charging cable into the base. I've printed it successfully using both PLA and ABS. Some supports will be needed, but...
thingiverse
Needed a phone mount for a 2019 Honda CRV and my OnePlus 7 Pro. Commercial options were $80+, and this was clearly a financial situation a 3D printer could solve. 5, 10, and 15 degree standoffs are included for custom viewing angles. Designing a...
myminifactory
A handy removable change holder that fits nicely into the compartment under the armrest of a Honda CRV mk4.
thingiverse
2002-06 Honda CRV has a poor cup holder design that causes drinks to tip over during a turn. ...This attachment fills in the empty space to hold drinks in place.
thingiverse
This is a cup holder that sits in the standard CRV cup holder and provides a base for larger cups or mugs. This holds the cup up so the other cup holder is useable. Updates still to come. ... [Big Macs also fit - version with fry holder coming]
prusaprinters
These are cup holder inserts/ adaptors for a 1st gen CRV. Should be printed in ABS but PLA prototypes has held up well so far.No supports needed The taller one can have its outer diameter reduced by roughly 1mm for it to fit better next to...
thingiverse
As I contemplate my future, I make a left out of the parking lot, giving the gas pedal some extra pressure, urging the CRV to hurry before the traffic catches us up. The power surges, the CRV turns hard, the latte goes airborne. My heart seizes with...
thingiverse
My CamelBak Forge drink bottle did not fit in the cup holders of my Honda CRV 2006, leading to it wobbling about all over the place and falling out. This print inserts into the original cup holder in the centre console. This can be printed in...
thingiverse
This is designed to replace the factory switch blanks in the dash of a 2002-2006 Honda CRV, for the purposes of mounting an auxiliary switch for things like light bars, fans, etc. ...This is a flat blank which will mount flush with the dash in flat...
thingiverse
Recently, I purchased a 2018 Honda CRV but hated both available mounts, so I designed my own in Fusion 360. I was learning Fusion 360 at the same time which is why there are two design methods (split and All-In-One). ... The second AIO design has a...
thingiverse
Caution, the gear shifter is not usable when the holder is in place I use this holder for longer drives. The base was printed at 20% infill to retain some flexibility for the clips The post was printed at 50% and trimmed with a Dremel tool once the...
grabcad
This is a collaboration of information I have gathered on the internet as well as a physical study. ...it is a lift spacer for Honda crvs 1 generation
thingiverse
Pieza adaptador tapa para surtidor limpia faros Honda CRV
thingiverse
Frame to adapt 6-inch speaker for honda CRV 2008-2011
prusaprinters
The temperature control dial cover broke on my moms 2013 Honda CRV, so this was made to cover up the bright light underneath.
thingiverse
The little clip to hold the bar that is used to prop up the hood (bonnet) on my Honda CRV. Designed to simply clip into the square hole where the old clip fitted. ... Works very well - updated file has a better defined clip mechanism to hold the clip...
thingiverse
Car (2006 Honda CRV) had a dummy mount for XM, and the factory antenna is not made any more. This fits a Sirius XM SV300 antenna, and bolts directly to the holes in the roof of the car. ...Uses M4 bolts and screws into the plastic.
thingiverse
I had a wiper reservoir that had a broken cap on a 2001 Honda CRV. I could not find a good design so I made my own. If you still have the dipstick, you can zip tie it to the end. I make lots of custom designs for prototypes, etc. Please see my...
thingiverse
Replacement hubcap for my Honda CRV How I Designed This Designed to print using aquasolve support for the indent and Honda logo on the front (underside of print). Use silver filament for the print. Keep an eye on the print while doing the support,...
thingiverse
A while back I changed out the sway bushes on a 2004 Honda CRV. The replacement bushes I used were Urethane. However I had to buy generic ones and cut them down with a knife to make them fit, as there are none available here for this model Honda. ...
cults3d
Designed for my 1997 crv. could work with others. sits in the rear light trim and is doublestick taped in. ...(3m foam tape)
thingiverse
Printed form PETG, mounted with two scews 6x30mm. ...On the right side is hole for charger. Phone is Samsung S7. Holder is designed to keep phone with transparent plastic case. ...