horizontal stand 3d models

This is a horizontal stand for UE Megaboom bluetooth speakers (80mm Diameter).

A much better/stable horizontal stand for the PS5. ...Can be easily printed with any material and slides into the PS5 plates.

This is an horizontal Gameboy stand, useful for my Gameboy clock project.

This is a horizontal stand for my awesome falcon 9 model. ... At least mine wasn't stable enough to resist my cat while standing upwards so I designed this vertical holder.

Horizontal stand for phones and 7" tablets. Print Settings Printer Brand: RepRap Printer: Prusa i3 ...

This iPhone 4 horizontal stand is suitable if you want to use your iPhone as webcam or if you just need a very firm and stable horizontal stand for it. Front and back camera have free sight and the 30-pin connector, home and on/off buttons are...

I could not find any good horizontal stands/converters for my HyperX Quadcast, so I made one myself. Works and looks decent =). After I finished printing it, I put some "furniture filt" on the bottom and where the mic "lands" on the stand. By doing...

Basic horizontal stand for UE BOOM 2. ...Easy to print, no supports.

HTC One M8 horizontal stand Print Settings Printer: Vertex k8400 Rafts: No Supports: No Resolution: 0,2mm Infill: 20%

ELGATO Stream Deck Horizontal Stand RECOMMENDATION: It is advisable to glue some rubber on the bottom to avoid sliding on the table during use.

This is a Horizontal stand for the Xbox Series X. This stand is designed for passive cooling of the system with fashion in mind. The rear stand is also designed for the ability to install an led strip for under glow. Enjoy If you 3d print this stand...

Mobile phone stand with variable width for landscape/horizontal viewing movies and playing games.

Stand for displaying Jrad's remix of Chemteacher628's falcon 9 horizontally.

As I found no 3D printable solution for my problem, I designed some quick clip-on stands to be able to lay my Logitech Speakers horizontally. ...It needs 2 stands per speaker, and angles them approximately 25 degrees upward.

This stand allows the KS0 to be elevated from the surface to provide additional airflow.

The MMU2 stand is designed for the IKEA LACK housing and two stacked Samla Dryboxes.

PS4 Fat Horizontal Holder To lift your PlayStation and avoid overheating at the bottom. As it is PLA, you can ensure that it will withstand up to approximately 60°C. I tried not to position in the hottest areas. ... Enjoy!

The stand holds phone tight, still comfy enough to manipulate with phone in stand (respond to msgs etc.), no need to pull the phone out of it. ...Print Settings Printer: Prusa i3 Plus Original ...

its a stand for the ps4 pro. not much more to say... ... just print in your favorite settings, i think youll be fine.

This stand was made using the fusion 360 optimization simulation to create the forme. ... It was print in 3hrs with an 0,2 layer hight and 7% infill and it is way stonger than it needs.

... allows for effortless docking of the console. No modifications to the original dock are required, just place the dock on top of the stand and you're ready to go! ... When the Switch dock is placed on the stand the total height is 3.25 inches tall.

The MMU2 stand is designed for the IKEA LACK housing and two stacked Samla Dryboxes. Rafts:NoSupports:NoResolution:0.2mmInfill:15%Filament brand:PrusamentFilament color:blackFilament material:PETG

This a a horizontal stand for the F9/FH model by Brian Mernoff.

This is a horizontal stand for iphone 5 to use Touch Portal APP

A new version of my original XBox One X Horizontal Stand / Riser (https://www.thingiverse.com/thing:3596481). Thanks for all those who added, liked and downloaded the original. ... Design transferred to...

A horizontal stand for the Fritzbox 7530. Raises it up by ~25mm to make sure it gets enough air flow from underneath. Optimized to be printed at .28 layer height with .4 layer width. ... I printed with PLA!

... to make easier to see in low light situations. UPDATE: 2/11/2018 I updated the horizontal speaker stand, now it fits better and won't tip over if speakers are nudged backward. Creative Speakers CA-3810 Horizontal Stand and volume control holder

... new to learn in Fusion 360, this was accomplished using PicSVG (https://picsvg.com) to generate a two-dimensional vector graphic from a picture. Alternative Version: XBox One X Horizontal Stand / Riser 2 (https://www.thingiverse.com/thing:4126584)

A horizontal stand for the original iphone 6. Can be fitted with glue strips on the bottom and mounted on a flat surface in your car, It also has a cut out for the power button, so you dont accidentally press it while inserting phone. I may revise...

Provides a stand for the Logitech G51 speakers when placed horizontally. The built in stands can be unscrewed which is what the picture shows. Extra bit on the side is required since the curved portion of the speaker is not centered. Would be...