hs1177 3d models

HS1177 bracket

HS1177 Camera All credit goes to Marcus Sargent from GrabCAD here https://grabcad.com/library/hs1177-600tvl-fpv-camera-1

needs 5-6 mm self tapping screws. ...resect screw hole to help clear hs1177 camera. ...large footprint for more surface area to mount with servo tape.

Lisam210 Schwenkfront HS1177

cam_holder_tweaker180_hs1177

TSX200 HS1177 FPV Camera Bracket

Low profile mount for the Turnigy HS1177 fpv camera. ...

Camera mount for HS1177 on the ZMR250. ...Attaches by fitting over standard 35mm high standoffs.

Designed to use a HS1177 FPV camera with a TSX mini quad frame (www.stantonframes.co.uk) You will require longer self tapping screws (5-6mm) to secure the HS1177.

Small adaptor to allow the use of a HS1177 in a ImpulseRC Reverb. ... Allows around -5 to 35 deg angle

Basic HS1177 Cam mount for the PEON 230, however may fit other ships that are 40 mm, 40 mm standoffs. ...

This is a hs1177 camera mount I made for an fpv plane. ...Mounts using 2 layers of 3m extreme mounting tape on bottom.

For FPV camera setups, use this bracket for the HS1177 size cameras, which include many Runcam and Foxeer cams. ...Bottom bracket not included.

I did some frame little modifications for use the camera Foxeer HS1177 Print Settings Printer Brand: RepRap Printer: Graber i3 Rafts: No Supports: No Resolution: 0.20 Infill: 100

The original side plates did not fit so I created those to mount my HS1177 camera. ...Updated 2016-04-23 to allow more inclination due to better position of mounting hole.

The Alien frame clone, Martian, doesn't easily allow to mount the swivel HS1177 camera onto the front side panels. Instead I chose to model this simple holder. ...Printed with PLA.

Spacer/washer for HS1177/PZ0420M to go between the bracket and housing. ...It increases the surface area and friction between the bracket and the camera to make it much more secure.

This is a little adapter I designed to mount a Runcam Owl FPV camera on frames with built in mounting locations for a 26x26mm HS1177 style camera. Pictured is a hive150 I am building, but it should work for other frames designed with the popular...

... the 30.5mm FC hole pattern and function as a 3mm spacer. There is also a 3mm FC spacer for the back 2 FC mounts. Print list: 1 x HS1177 FC Front mount 2 x 3mm FC washer/spacer note that you might need a longer M3 screw to mount the FC to your frame.

The mount is made to fit a HS1177 camera, other may fit and of course it's not specific to the TSX frames, it could be fitted to any frame. ...Print Settings Printer: SmartrapcoreXY ...

Simple seat for the HS1177 FPV camera in a Deformation Insect 130mm frame. This should fit nicely and provide good up tilt. included are 15 degree, 20 degree and 25 degree versions. It turns out this fits the Grasshopper 160 (G160) frame quite well...

A something simple to hold the hs1177 cam to a standard board mount on my emax night hawk. ... i used a bit of shoegoo to hold or you can slightly heat it and push the sides in to make a tighter fit.

Carcasa para la cámara FPV hs1177 de foxeer, también es válida para la runcam swift u otras con ese mismo formato. Ha sido testeada y cumple perfectamente su función. Requiere roscar, posteriormente a la impresión, la parte donde se...

... to the Blackout mount. ...Snugly holds an HS1177 camera by mounting to the standoffs (30mm center to center). Either bolt down or use double sided tape. ...You will have to come up with screws to hold the camera to this, the stock ones are a joke.

This is a backplate for a Foxeer HS1177 FPV camera that allows a nano-servo to be mounted to the back which, when installed properly in a quadcopter frame, allows the entire camera to be tilted up and down with minimal weight gain or installation...

A 20deg mount for the HS1177 on a ZMR250 rig. 20 deg is about as steep as the camera can tilt whilst keeping it inside the frame without modifying the top plate. It take a decent amount of force to get the camera inside the mount, once it is in, it's...

This is a remix of the HS1177 Mount from sledgehammer46 adjusted to fit the LS210 Frame. The Base for the Cam is the same but the Mount is redesigned to fit the smaller frame of the LS210. It has markings for 15° 25° 35° and 45°. Beside the original...

A simple camera protector that is held in place by the lens and lock-nut on the hs1177. There are two versions. V1 is minimmalist and very snug fit to the 2.1mm lens. V3 is larger and protects the camera body a little more. Both may need to be...

This mount was designed for the HS1177 Camera. It's commonly referred to as a 25x25mm fpv camera. Two versions: Light and reinforced. You probably don't need the reinforced one, that's mostly for horizontal stabilization but it's your choice. ...

This is a piece to hold the HS1177 to a ZMR 250 frame without the bracket included with the camera. The screws needed to secure it are the ones that come with it, no need to use others. It allows for a tilt of about 30 deg. The weight of the printed...