hue bridge versions 3d models
1453406 3d models found related to hue bridge versions.
grabcad
Philips hue Bridge Version 3 - See my Philips Hue Bridge – Wall Mount!
thingiverse
Philips hue Bridge Version 3 - See my Philips Hue Bridge – Wall Mount here: https://www.thingiverse.com/thing:2960677 # Do you like what you see? ... <a...
thingiverse
Our Hue Bridge mount known from Etsy and Amazon now available for free on thingiverse.
thingiverse
A simple topplate for the Philips Hue Bridge (2). It covers all the lights, but leaves a hole to push the button. ... You can just put it on top, or ad a small amount off double sided tape, to keep it in place
prusaprinters
This is a print of a bracket for mounting Philips Hue Bridge to a wall. Features: tight friction fit for the bridge ability to mount the bridge without disconnecting wires does not block access to the button and LEDs screw holes for either vertical...
grabcad
For more information visit: https://www.studiopieters.nl/philips-hue-bridge-wall-mount/ Update: Philips Hue Bridge – Wall Mount V2.0 :: 18-06-2018Changelog: Changed desig to reallife dimensions More esthetic designFor more information visit:...
thingiverse
I created this Philips Hue Bridge Cover to block the bright blue LED Lights since they annoy me at night. The Hue Bridge is located in my Bedroom. Also black matches my setup better. I used Black PLA to print it. The walls are 2mm thick, it has...
thingiverse
Small wall mount for the Philips Hue Bridge. You can use any of the 5 screw holes. ... Bets to print with 100% infill.
thingiverse
Remixed: https://www.thingiverse.com/thing:4979528 To be able to rack mount a Philipps Hue Bridge - Fits like a glove.
thingiverse
Update: Philips Hue Bridge – Wall Mount V2.0 :: 18-06-2018 Changelog: - Changed desig to reallife dimensions - More esthetic design For more information visit: https://www.studiopieters.nl/philips-hue-bridge-wall-mount-v2-0 # Do you like what you...
thingiverse
It's a pegboard holder for the Hue Bridge. I basically just took the screw hole pattern from the HUE rack mount and cut it out and put the Pegboard hooks on the back of it. ... I have printed one out myself and it works great, the fit it a bit tight,...
thingiverse
Wall mount for round Hue Bridge v1. Designing and printing the mount was easy. Drilling holes and feeding power and network through was hard. ... (Or you could run the wires however you like)
thingiverse
In spite of the fact that they're stoooopid expensive, I decided to use Hue Lightstrips (2nd generation) in my LED Bridge Lamp, so I modified a few parts from Opossums' stellar design to facilitate that. Here's what's included: light_guide_AB-hue...
thingiverse
This is a cover for the Philips Hue Bridge (gen. 2) to cover up the LED's on the front. It is adviseable to print in another color that white, since the LED still shine through 5mm (100% fill) white PLA. It clicks right on the front of the Bridge.
thingiverse
Simple Philips Hue Bridge case which is covering annoying blue led lights. For now it's holded by double side tape. In future I will model some holder where it can be attached via screws and also some front cover. ... I recommend to start printing...
prusaprinters
Holder for Philips Hue Bridge v2 to the SKÅDIS pinwall.Model is very fine and flexible (only 1mm walls). There is no weight to support. <br>I didn't add the locking pins - it's held down by the cabling.</p><p>Needs supports to print. ...The...
pinshape
The philips hue bridge got crazy stong LEDs that can light up an entire room. Unfortunately it is not possible to cover it with tape since the LED holes also act as air vents for hot air. I designed this cover that has a ≈2mm gap across the top and...
thingiverse
Using Home Assistant on a Raspberry Pi 4 with an SSD, I mounted them to a DIN rail using these fantastic mounts: https://www.thingiverse.com/thing:2610621 Now I also wanted to mount my Hue Bridge so I made this remix. Note that it is facing the...
prusaprinters
It features:tight friction fit for the bridgeability to mount the bridge without disconnecting wiresdoes not block access to the button and LEDsscrew holes for horizontal mounting patternsdesign optimized for 3D printing thus 45-degree angleswall...
prusaprinters
Remix of the original design from Luther2k published here: https://www.thingiverse.com/thing:3385969The main difference against the original is the possibility of screwing the mount on any side of the rack. This was not possible as “pins” are...
thingiverse
Curved Bridge with three different arches to choose from. ... The planks on bridges have random spacing and sizes
myminifactory
This bracket allow for the Philips Hue Bridge 2.0 to be rack mounted.
thingiverse
Didn't like the existing Hue Bridge mounts and their not so exact covers.
thingiverse
Quick and easy design to cover the Philips Hue 2nd gen bridge to block the blue lights from it.
thingiverse
Wallmount for Philips Hue Bridge with easy clip in system for quick exchange. Work in progerss! ... Next step: screwholes will added Please feel free to add other wishes.
thingiverse
(deutscher Text unten) My HUE Bridge could only poorly reach the outlet in the garden shed. After I put it on edge, the connection to the shed was much better. So that it also remains upright, I have designed the stand. Update 07/2021 After my...
thingiverse
I redesigned the 'Socket mount with cable management for Philips Hue Bridge' by hashtagmarco as a support-free print version. After I printed his original version, the thin connector clip broke off and the support was difficult to remove.. I...