huina 580 3d models
1320 3d models found related to huina 580.cults3d
This is the direct replacement for the huina 580 engine cover. ...It is based on the Komatsu PC290.
cults3d
dogbone for huina 580 excavator std is longer than stock one, usually make things right but for customs applications use longer arms
thingiverse
This bucket is setup for the huina 580 bucket pins. 29mm spacing pin to pin. 31mm inside width. To print it I would suggest printing with bottom of the bucket vertical. ...use supports for bottom.
thingiverse
I created this part to help increase the bucket curl for the Huina 580. check out the youtube video to see how much more it curls. this will also require grinding the support that attaches to this so it does not stop early on the curl. ...
thingiverse
Huina 580 excavator ripper attachment, use pla or pla carbon fibre or any other strong filament. see video of it in use. ... https://youtu.be/8B989e6-CwM PRINT AT 100% INFILL YOU WILL NEED TO REAM OUT THE BOLT HOLES AS IT WAS DESIGNED FOR TAPPED...
thingiverse
this is a door replacement for the Huina 580 door which is cut out. this fits in place and is screwed into the door pillar. requires cutting out existing door on rc model. M2 screw for the hinge. drill hole into existing huina with M2 hole size. ...
thingiverse
This is a fast changer for the scoop of a Huina 580. The spring has to be used from a pen. It's only compatible with scoops. Not with the wood picker or the hammer. Print it with 100% It has to be strong... H@ve fun! ... UPDATE 21.06.19: I...
thingiverse
the battery compartment of your Huina 580 is too small for you and you do not need a smoke generator, then I have an alternative here. I have designed a battery compartment that offers more space for a larger battery by eliminating the smoke...
thingiverse
These buckets fit with the 580 from Huina. These are 3 different bucket configurations you can use. ...They are strong and will dig heavy material.
thingiverse
Larger capacity Battery tray for the Huina 1580/580. It is as simple as print, remove old tray and install new tray! Direct fit to the stock battery tray location! Will require removal of the smoke unit. ...Tray dimensions are 118mm Wide x 52mm x 17mm...
cults3d
... excavator. ... With the device you can shorten the bushes or shorten other grasses. Light comes on when the engine is turning. A 540 motor is needed and a jack plug. It comes with a Volvo EC160 intake and a Huina 580. ... FOR OWN USE ONLY !!!!!!!
thingiverse
** Ripper for the Huina 1550 / 550 Excavator ** * Needs (3x) M2x8 screws for the pads * OR use it without pads for easier ripping in hard ground V2 corrects a clearance issue with my Spring Coupler (https://www.thingiverse.com/thing:3732951)
prusaprinters
Ripper for the Huina 1550 / 550 Excavator Needs (3x) M2x8 screws for the pads OR use it without pads for easier ripping in hard ground V2 corrects a clearance issue with my Spring Coupler (https://www.thingiverse.com/thing:3732951) Print...
cults3d
Offer here a shaft lift for a Volvo EC160 full metal track excavator or Huina 1580. The lifter is made of 3D printing PLA and the blue pratzen made of TPU.(Rubber). It's all screwed and nothing glued or anything. Soon there will be 2 different...
cults3d
Block tongs for concrete blocks for lifting and setting down. ... Blocks up to 5cm wide STL file for private use only !!!!!!!
thingiverse
** Spring-loaded coupler compatible with the Huina 550 / 1550 or 580 V1-V2-V3** ** Does NOT fit 580 V4 bucket, I will try to remix it if I can get dimensions ** ********** ** For the 580, use the "580_Spring_Coupler_xxx.stl" files ! ** ********** ...
thingiverse
** Huina Excavator Electric Coupler ** *** Use the 580_ labeled files for the 580 / 1580 v1 v2 v3 v4** ** UPDATE ** Someone made a printable lead screw version for use with "D-shaft" N20 motors. * "Electric_LEAD_Lock.stl" * "LEAD_Screw.stl" ! Liski...
prusaprinters
Huina Excavator Electric Coupler * Use the 580_ labeled files for the 580 / 1580 v1 v2 v3 v4 UPDATE Someone made a printable lead screw version for use with "D-shaft" N20 motors. "Electric_LEAD_Lock.stl" "LEAD_Screw.stl" ! Thanks to m. ...Liski for...
prusaprinters
Spring-loaded coupler compatible with the Huina 550 / 1550 or 580 V5 has more clearance added for the bucket, lock and bolts parts. Shouldn't need much filing/sanding. Also added a bevel to make hooking a bucket easier. If V4 worked fine for you,...
cults3d
engine hood for huina 580 Can accommodate hydraulic system and larger battery
thingiverse
dies ist eine stampferplatte für den huina 580 meisel das projekt habe ich selbst entworfen
thingiverse
Narrow bucket for the Huina 580 excavator. 40%infill printed with the bucket pin part facing down on the plate for printing. only supports from base. ...
cults3d
This is a vibrating plate compactor for the Huina 580. these are just the files to make the plate compactor. It still requires the motor and rubber isolators which I used Servo rubber mounts to fit. If not then 5mm rubber with a 3mm hole will work as...