ichabod jr 3d models
2883 3d models found related to ichabod jr.thingiverse
Parts for the Shendrones Ichabod Jr. Print in TPU. Cammount 2 has a bigger hole on the side to facilitate Hero removal, and a bigger hole for the fpv cam lens. ... Cammount_m4 and plug_m4 are updated versions using an m4 x 30 bolt, 2 washers and a...
thingiverse
Made a quick hard mount for the shendrones ichabod jr to tune my pids because with the RSGo soft mount you do not see vibrations, bounceback and stuff like this
thingiverse
Wanted to be able to use a TBS Unify VTX on my Ichabod Jr, so remixed Andy's original Design. ... Print in TPU (ideally Sainsmart TPU) Here is another version which will wrap around some 8mm long standoffs as personally I'm not too keen on screwing...
thingiverse
Servo actuated camera mount for Ichabod Jr. You'll need two 5x10x4 bearings (5 id, 10 od, 4mm wide) and a 35mm m3 standoff for the pivot. The standoff slides in from one side and is secured with an m3 screw. The landing gear takes the load of landing...
thingiverse
So being the overcautious miniquad builder that I am, I was concerned about the battery sliding forward and the cells or leads being cut by the stack cover plate on the Ichabod Jr. So I designed this 'Battery Bump Pad' as a nice spongy surface for...
thingiverse
Found this servo laying around, figured it would be perfect to use on the ichabod. Stock mount for 9gr servos didnt fit, so designed this one. ...Same principal different servo.
thingiverse
Shendrones Ichabod Jr style mount for Flywoo Mr Croc Printing in TPU 60% to 100% infil
thingiverse
Wanted to be able to use standoffs on the front of my Ichabod Jr. ... Print in TPU (ideally Sainsmart TPU) Revision Note: No longer work in progress, previously the holes to wrap around the standoffs were DIA 6mm (incorrectly) so has now been...
thingiverse
This is a simple GPS mount for Matek SAM m8q for the Shendrones Ichabod Jr you can print it on tpu (double side tape for gps inside) you can remix it or improve joining with the Immortal antenna mount for more robust design, if you do it send me the...
thingiverse
Wanted to be able to use standoffs in the rear of my Ichabod Jr as personally I'm not too keen on screwing into the TPU or using a longer screws and adding nuts. Print in TPU (ideally Sainsmart TPU) Revision Note: No longer work in progress,...
thingiverse
This part allows you to mount a TBS style SMA connector to the rear of the ShenDrones Ichabod Junior at a 45 degree angle. This version screws straight into the TPU as Mr Shen intends for it to be, but if you would prefer to use 8mm standoffs print...
thingiverse
Lens protection for the GoPro and I moved the DJI FPV camera holder a little bit forward to get the lens out of view. ... Not my best work, but do the job fine.
thingiverse
Damped Hero Mount for using ReelsteadyGo with Hero7. Print in TPU. The arms slot into the holes in the back of the cam mount, and the top mount slides back and forth to change cam angle. Use the negative nose plug for negative cam tilts. ...Work in...
thingiverse
Shendrones Terraplane HydroPhobe Ichabod Jr 2.0 GPS BN220 SMA Immortal-T 25mm Stand Off / Spacer I made another one for another format of GPS you can find it by searching "GPS Terraplane" in the search For 25mm spacer
thingiverse
I'm in the process of building up my ShenDrones Ichabod Jr and wanted to be able to use a RunCam Micro Eagle, but discovered that it doesn't fit the standard servo compatible camera mount properly, so I modeled this up as a solution. This camera...
thingiverse
This part allows you to mount a TBS style SMA connector to the rear of the ShenDrones Ichabod Junior at a 45 degree angle. This version enables the use of 8mm long standoffs to separate the plates - I have also uploaded a version for screwing...
thingiverse
Cam holder for use with 25mm StandOff
thingiverse
Support for GPS SMA and Immortal T for 25mm spacer. ...For the Shendrones Terraplane Not Suitable for BN220 I made another one for another format of GPS you can find it by searching "GPS Terraplane" in the search
thingiverse
FR7 Style Hero 11 Mini Mount for Shendrones Ichabod Jr. ... Horizonal Immortal T mount w/wo TBS ND Filter
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = JR. ...stick_width = 8 hole_radius = 3 flat_bottom = 1 Font = write/orbitron.dxf stick_thickness = 3 font_thickness = 5 font_size = 10
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = JR stick_width = 8 font_size = 10 Font = write/orbitron.dxf hole_radius = 3 stick_thickness = 3 font_thickness = 5 flat_bottom = 1
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=753477 Instructions Using the following options: size = 20 spacing = 1 extrude = 5 direction = ltr web = 0 font = Trocchi text = Jr
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40704 Instructions Using the following options: ring_size = 18.14 Font = write/Letters.dxf message = JR ring_width = 6 font_spacing = 0 ring_thickness = 1.6 font_size = 10
thingiverse
... that camera in. Runcam micro mount for Fusion is for 2.3 lens, slips into the micro mounts for any cam tilt angle. Ichabod_hero and Ichabod_session are for hs1177 sized cams, the others are for micro cams. ... Added micro cammount for 2.1 lens.
thingiverse
TPU parts for Shendrones Hydrophobe. ...Cam mounts are shared with Ichabod Jr.
thingiverse
This is a remix of the ichabod dji hero 8 mount with immortal T added.