iflight megabee 3d models

Wallmount for iFlight MegaBee cinewhoop.

Ducts for iFlight Megabee V1 cinewhoop frame.

iflight megabee v2 ducts TPU optimized

iflight megabee v2 ducted for tpu filament add v2a

A duct I made for iFlight megabee frame. Compatible with at least the first version on the megabee. ... Print from PLA with maybe solid infill since it's not very thick anyway.

76mm props need 4x 5mm O.D standoffs (25mm for 20xx motors) NOTE ! ...this is for megabee V1 only

Iflight megabee V2 Low Profile Ducts

Inspired by Laurent Athenol's (Frame-Concept) "Bee Bumper" CineWhoop designs, I created these custom dual ducts for the iFlight MegaBee v2 frame. They are supposed to be printed in PETG and have a guide rail for adhesive sponge / foam / neoprene...

Mount to use gopros own mounting system on your iflight megabee. Print out of PLA and put M5 nut on the other side, you can use the screw that came with your gopro. Of course you can mount pretty much anything with this style mounting system...

This is an enhanced dual duct for the iFlight MegaBee (original v1 version). It has an angular aerofoil shape and super small tolerance/clearing to uncut 3 inch ducts, giving it MUCH more additional lift than the original ducts it came with and also...

GoPro8 Mount for Megabee 15°

Custom made design Tpu ducts for Megabee v2.1 made from Tpu and abs for maximum strength and maximum throttle with removable rings.

Made these parts to get the ducts out of DJI camera view and to have the antennas mounted clean. ... Some notes: - You need 3 20mm standoffs and 6 M3 cuphead screws to assemble the cam cage - You need to print 2 antenna standoff mount and tube mount...

Printed for iFlight Megabee

15 and 30 degree mount for the hero 8. ...Fits the Iflight megabee v2

GoPro style anti shake support for iFlight Megabee v2 drone. ...I used 5mm rubber pads and a clamp to prevent the top from getting lost.

... ...I didn't like the red TPU that was included with the MegaBee HD, and iFlight never responded to my numerous requests for the STL to modify, so this is a design made from scratch to mount the DJI Antenna as well as an XT30 plug for a neat look

GOPRO Mount for iFlight Banshee winth 10º.

I modified the megabee duct in order to reduce the clearance between duct and 75mm gefman squirt prop PROP https://bit.ly/38iatyP DRONE https://bit.ly/37fRnIq

TPU-Mount für eine GoPro 8 auf einem iFlight MegaBee CineWhoop Copter. Die Aufnahme passt auf einen MegaBee Frame von iFlight, ober vergleichbare Copter mit einem Bohrbild (Breite:23mm x Länge: 37mm), weitere Bohrbilder für andere Frames folgen Im...

These parts are to upgrade an iFlight MegaBee V2 cinewhoop to use a DJI Air Unit. You'll need to drill a couple of new holes in the top plate to fit the air unit using M3 nuts and bolts. The antennas fit in the tubes and can be angled for best...

This is my Gopro 8 mount, with it's optional "BOOT" protection sleeve. You get best results, when printing the sleeve with a silicone like fillament as Ninjaflex 45, >30% infill. ... For the support I would recommend 95 TPU, at 30% infill.

Hero 8, 25 degree

GoPro Hero 7 15 degree

flexible tpu case about 15° for flight meagre v.2 works with reel steady

Ducts with large wall for TPU.

Naked GoPro upside down mount with 4 siliconedampers. Slot for tbs nd filter. ... You'll need four of these siliconedampers...

TBS Crossfire Immortal T antenna extended holder. This holder moves away antenna ~ 30mm from rear stadoffs so it fits behind ducts. It also lift antenna ~20mm It should fit to other quads with 5mm diameter standoffs / spacers. Hole is 5,5mm. ... ...

Sturdy design to support a Gopro without the risk of breaking the mount. Tried and tested! :) Print the bracket and add a M5 self-locking nut (which can be found very easily in DIY stores) In the model is also included a screw to limit the risk of...

i couldn't found a gopro8 mount for iflight megabee with ND filter so i remixed two files