ipad dash mount tacoma 3d models

This is an iPad mini slider I redesigned to fit over the top of the factory audio unit in the 2005 Toyota Tacoma. I have the .stl file in one whole piece as well as split in half to fit on my smaller printer. This is not a perfect print but is...

This is a simple dash mount I remixed to hold a backup camera screen for my RV, it would also work well as a phone mount with a magnet mount.

A Toyota Tacoma dashboard bracket that fits the ball mount from a 5" camera display. It fits a 2022 but should work on any 3rd gen Tacoma. I printed in PETG but PLA might be strong enough, the bracket body is thick and sturdy. ...I added some small...

A Toyota Tacoma dashboard bracket that fits the ball mount from a 5" camera display. It fits a 2022 but should work on any 3rd gen Tacoma. I printed in PETG but PLA might be strong enough, the bracket body is thick and sturdy. ...I added some small...

This is a 2 piece mount to put a magsafe charger in place of the airbag switch on a 95-04 Toyota Tacoma. Print the Magsafe piece laying down Print the dash clip piece on its side with supports. ...If you print it laying down the tabs will most likely...

An iPad mini mount for the front cupholder in a 3rd gen Toyota Tacoma. This replaces the OEM middle divider part. The bracket is sized to fit an iPad mini 4 in landscape. I might build a larger size for an iPad if there is enough space. ...If requested,...

An iPad mini mount for the front cupholder in a 3rd gen Toyota Tacoma. This replaces the OEM middle divider part. The bracket is sized to fit an iPad mini 4 in landscape. I might build a larger size for an iPad if there is enough space. ...If requested,...

Toyota Tacoma Dash Camera Mount (SJ4000/GoPro)

This is a Dash Cam mount for a 2013 Toyota Tacoma. It mounts a SJ4000 camera (may fit GoPro's) discreetly up behind the rear view mirror. The mount clamps to the rear view mirror post and uses a few 4-40" Screws and Heat-Set inserts for mounting.

This is a Dash Cam mount for a 2013 Toyota Tacoma. It mounts a SJ4000 camera (may fit GoPro's) discreetly up behind the rear view mirror. The mount clamps to the rear view mirror post and uses a few 4-40" Screws and Heat-Set inserts for mounting. ...The...

Had a 1" RAM mount laying around. Increased the size of the ball to 1". ... Edit: 7/15/22 - Added some support to the ball after having one snap.

F15 dash camera on the factory GoPro mount to the right of the rearview mirror. The Papago is available around $30 and doesn't leave an expensive gopro sitting on your dash when you're not in the vehicle. ... You can also wire it into your overhead...

Two adapters to mount a dash cam to a GoPro mount. One for the G1W type cameras. And the other for the TOGUARD Blue camera. (https://www.amazon.com/dp/B01F0NJ56G/ref=cm_sw_r_tw_dp_zeGDxbT6S5EP2) Version 1.6 for better fit to Togaurd, Also covers...

Took the design from Cracked1 and adapted it to fit my radio or radio Mic that has a clip backing. ...Fits perfect for baofeng radio or Rugged Radio Mic.

Ford mustang ipad mini dash mount 2011-2014

... not sag or curl) * printing in multiple pieces. The prongs will be pushed inward when inserted into the Tacoma dash. So if you print the button along the top/bottom, the prongs will shear along the layer lines (i.e. ...it will break very easily).

I used to sit my iPad mini in the pull out tray in the center below the dash and use it as a dedicated GPS on long road trips, but I got tired of it sliding around and being so low in my field of view, so I remixed the excellent iPad mini holder by...

This is an alternative to another iPad mini mount that I created for my fan attack Clubsport VE2.5 wheelbase. This one mounts to the side instead of on top. It can also be printed in one piece. It will simply mount using the existing bolts on the...

... it on smaller size printer beds. ...So you will have to glue part one to the back of part two before mounting it on your Clubsport wheelbase. This bracket will hold A standard iPad mini in landscape format allowing for data port access on either side.

Simple dash stand for iPad or iPhone with otter Box. Design for holding a iPad in our work truck to use Google maps. Just put two way tape on the bottom and it should keep your iPad with Otter box in place. ...

Simplified Dash Blank for Toyota Tacoma. Might be a tight fit. ... I recommend printing in the original .stl orientation (see attached pic).

The dash clock in most first generation Tacomas is broken by now, and if it's still working it is in an odd location, hard to see behind the steering wheel. Mine was broken so I decided to replace it with a universal 4-hole holder. ...I use it to hold...

Cover for 1st gen toyota tacoma. ... PLA is fine and seems to work great

Dash Cam Mount Holder for YI dash cam and Anker Roav DashCam A1

Simple fitted phone mount for 2016+ Toyota Tacoma.

Just needed something to hold a magsafe charger in my car, I drilled this into a hidden part on the dash to hold my phone. ...the ball is 17mm diameter and should fit gps type stuff.

plate to mount hopkins insight brake controller in a 3rd gen tacoma. ...replaces useless cubby on left of steering wheel.

Switch blank for a 2nd Gen Tacoma center dash. ...Print a .2 res and 0 infill.

Switch blank for a 2nd Gen Tacoma center dash. ...Print a .2 res and 0 infill.

...... I created this UV5R Radio mount for my 2010 Toyota Tacoma TRD Off-Road. I printed it face down without any issues. It is designed to be used with the belt clip provided with your radio. I added 3M automotive mounting tape to the back of the mount.