iphone bike mount 3d models
403458 3d models found related to iphone bike mount.pinshape
This is an iPhone 6 Bike Mount with a little bit of style. I designed it for my girlfriend because she likes sunflowers :-) I hope you enjoy it too! Please note that the designe is made to fit a iPhone 6 with a slim case. ... Instructions: Print the...
thingiverse
... parts on the case & mount for a super snug fit. (This will take 10 minutes or so). Fasten spring piece to bike mount with m5 or other small screw Zip tie/hose clamp the mount onto your stem. ...Clip your phone in and ride to your heart\'s content.
thingiverse
Customized version of http://www.thingiverse.com/thing:614516 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=614516 Instructions Using the following options:...
thingiverse
Awesome Bike Mount Instructions Print on solidoodle 4 with ABS at 209 for extruder and 109 for bed.
prusaprinters
(Thicken or thin depending on your case and phone type) This specific STL file is designed to fit an Iphone 10X with Otterbox case. If the the mount is too big for the goose neck of the bike, you can use foam tape to spread out the clamps a bit. -...
thingiverse
... a WIP, made to attach to a square fork arm. ...May make a more universal clamp later. m3 bolts and nuts are used to mount to the arm, and a 1/4" bolt and nut for the tilt adjustment axis. ...Will be updating this as the project further progresses.
pinshape
SummaryMy girlfriend asked me for a iPhone 6 Bike Mount with a little bit of style. So I designed this sunflower style phone dock for her Bike. She likes it :-) Hopefully you like it too! Please note that the mount is designed for an iphone 6 with an...
thingiverse
My girlfriend asked me for a iPhone 6 Bike Mount with a little bit of style. So I designed this sunflower style phone dock for her Bike. She likes it :-) Hopefully you like it too! Please note that the mount is designed for an iphone 6 with an slim...
myminifactory
Link: https://www.myminifactory.com/object/3d-print-iphone-6s-bike-mount-138461 ______ This thing is a simple bike mount for an iPhone 6s. You can easily attach it to your bike with up to three zip ties. Before printing, please check whether the...
thingiverse
Customized version of http://www.thingiverse.com/thing:426872 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=426872 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:426872 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=426872 Instructions Using the following options:...
thingiverse
This is a bike mount for an Iphone X that is housed in an Otter Box defender case. The mount bracket may need to be modified for different size bike mounting. Everything is assembled using 1/4 20 bolts, washers, and nuts. I recommend lock nuts since...
myminifactory
This thing is a simple bike mount for an iPhone 6s. You can easily attach it to your bike with up to three zip ties. Before printing, please check whether the part fits on your bike. The holder is designed to fit on round objects with a diameter of...
thingiverse
The mount for puttin it on a bike is meant to be attached justing epoxy putty, and is made to attach to a 1 inch piping on a bikes handle bars. ...Watch my video about making these files here!https://www.youtube.com/watch?v=9uqF4ZbaU1c feel free to...
thingiverse
The mount can be attached to any tube/stem of the bike smaller than 34 mm. The part can be fixed to the bike with cable ties. To avoid damaging your bike, please consider placing a soft material (e.g. rubber) between the part and your bike before...
myminifactory
The mount can be attached to any tube/stem of the bike smaller than 34 mm. The part can be fixed to the bike with cable ties. To avoid damaging your bike, please consider placing a soft material (e.g. rubber) between the part and your bike before...
thingiverse
This is a simple iPhone 4/4s handlebar mount for your bike. It is pretty tight but in return it does not fall of while riding. You are still able to plug in the dock-connector, audio-jack and use the speakers and side buttons. There is a version for...
thingiverse
This is a simple iPhone 5/5s handlebar mount for your bike. It is pretty tight but in return it does not fall of while riding. You are still able to plug in the dock-connector, audio-jack and use the speakers and side buttons. There is a version for...
thingiverse
When you print it and build it your ready to attach this to your bike and record or anything else. ... (the mount itself might not fit so you might need to remix I measured it with a different bike)
thingiverse
A bicycle mount for the iPhone 5. To be used without a case. Mounts on most sizes of round bars both horizontal and vertical using the OpenSCAD file. A 4/4s version could be made with very slight modifications. Edit: I added an OpenSCAD file for...
thingiverse
This thing is a two part iPhone 6 bike mount. One part is strapped to the handle bars using cable ties. The other is a case for the phone. The two parts allow a simple 1/8 turn snap lock to securely mount the phone. Removing it is just as easy. I...
prusaprinters
This thing is a two part iPhone 6 bike mount. One part is strapped to the handle bars using cable ties. The other is a case for the phone. The two parts allow a simple 1/8 turn snap lock to securely mount the phone. Removing it is just as easy. I...
prusaprinters
This revision cleans up the originals non-manifold portions as well as add the option to allow the user to mount their phone in landscape, as well as portrait. Category: Mobile Phone
thingiverse
This revision cleans up the originals non-manifold portions as well as add the option to allow the user to mount their phone in landscape, as well as portrait.
cults3d
So I sliced up the original design so I could get the mounting bit rotated 90 degrees. I also extended it so it would sit a bit higher up given the new location. The original was one part which seems nice on the surface but creates a print that...
thingiverse
So I sliced up the original design so I could get the mounting bit rotated 90 degrees. I also extended it so it would sit a bit higher up given the new location. The original was one part which seems nice on the surface but creates a print that...
thingiverse
Customized version of https://www.thingiverse.com/thing:912161 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=912161
thingiverse
Customized version of http://www.thingiverse.com/thing:426872 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=426872 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:912161 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=912161