jk dash bar 3d models
84241 3d models found related to jk dash bar.cults3d
I purchased the Vector Off-road JKE full bar link for my 2018 Jeep JK and its really been a great product. The one thing I didn't like was the messy wires hanging down to the USB power plugs. I needed a way to power the mounted electronics, without...
thingiverse
I purchased the [Vector Off-road JKE full bar](http://https://vectoroffroad.com/collections/jk-wrangler-products/products/jke-dock-2011-2017/) for my 2018 Jeep JK and its really been a great product. The one thing I didn't like was the messy wires...
thingiverse
2007–2018 Jeep Wrangler JK/JKU Dash Mount ==================== This dash mount will allow mounting of 3 devices on a Jeep Wrangler JK or JKU. I'll be adding additional mounts in the future. Ram Mounts --------------------- The v2 Ram mount is...
cults3d
This fits a 2011-2018 JK. This is a push fit design. The inlay replaces the factory inlay and just pushes into place. The letters will need to be printed with a negative horizontal compensation from -.10 to -.20 depending on the printer. This...
thingiverse
Working on a dash mount for my phone. I left a little slack in the dimensions to facilitate the silicone cover I have on it. ...V2 has 4mm of surround lip instead of the 3mm from the first version.
thingiverse
... ...This was modeled for a 2008 JKUR Jeep Wrangler Unlimited Rubicon, but should work on the first iteration of JK's (2007 - 2010) regardless of trim level. To install: 1. Slide the left side grab bar cover off (it slides towards the driverside) 2.
thingiverse
Am thinking of adding loop to allow securing to hanlde bar with a cable tie - although the fit is quite tight so is probably not needed, but a nice to have for peace of mind. ... This print allows for the tyre pressure monitor display on left (single...
thingiverse
This is attached to the inside of the dash cubby, with two sided tape and rubber debris catch still in place/removable. The small v notch could be a bit smaller, but wanted to be able to remove the debris catcher after installation. The 17mm ball...
thingiverse
https://www.thingiverse.com/thing:2355327 I used some bungees for hanging stuff from the horizontal top bar but it was difficult to hook and unhook items. After a series of 3 creation failures (PETG is very flexible) I ended up incorporating hook...
thingiverse
These are just two spacers to mount an OPT7 50" Light bar on your JK with the Rigid Industries Light bar mounts. Please hit like if you like it. ... Cheers Stanley
thingiverse
This bracket allows the dash to sit on the riser itself rather than relocating in another area by other means. Due to the relocation of alot of dash wiring, I had to make an outward semi circle to accommodate space for it so it wouldn't pinch the...
thingiverse
I just added some side supports. Might not be necessary, but made me feel better, lol! ... Remixed from: https://www.thingiverse.com/thing:4846219
thingiverse
Customized version of https://www.thingiverse.com/thing:3016108 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3016108
thingiverse
Customized version of http://www.thingiverse.com/thing:58001 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58001 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:536486 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=536486
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of http://www.thingiverse.com/thing:40705 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40705 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:536486 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=536486 Instructions Using the following options:...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _labelDepth = -0.3 _part = top _base = 0.8 _labelFont = write/orbitron.dxf _rows = 2 _columns = 4 _lipHeight = 2 _walls = 0.8 _labelText = JK...