jobo 2400 3d models
1194 3d models found related to jobo 2400.thingiverse
This is a piece to repair the lever on Jobo lift Esta es una pieza para reparar la palanca del lift de la procesadora de negativos Jobo CPP-2
sketchfab
YT-2400. Scanned from the X-Wing game model. The smoothed out area on the bottom is from the stand holder. ... Scanned with an Artec Spider.
thingiverse
This cog is only for Jobo Duolab processor and JoboDrum 2800 or Unitank 1500 series. ...
thingiverse
Needed a replacement magnet for one of my Jobo film developing tanks so designed one - has been working well for a year so thought I should share. ... This one done with 0.4mm nozzle, 0.2mm layers in PLA, the flat face down and supports on, and 20%...
thingiverse
... use it (although that's unlikely!!). Instructions Get a JOBO GPS unit without a tracking button (hard to get I imagine). Print the button Open GPS unit and place new button in position. Close GPS unit. ... Take photo of your new handy work.
thingiverse
Since jobo reels are so expensive and hard to find, I modified the existing design so that paterson reels could be used with the Jobo. Rotate the parts 180 degrees in your slicer. These parts should be printable without support material. ... All...
thingiverse
This is a spare part. ...It helps you to wind up two 120-films on one Jobo reel. ...On the picture you see the 3D-printed to the left and the original to the right.
thingiverse
The Jobo CPP-3 processing machine has its water overflow port in a location that's significantly lower than the CPP-2, and it prevents the water level inside the machine from being adequately high. Its my understanding that this change was made to...
thingiverse
The small JoBo tank is the smallest and least expensive development tank to be used with the 4x5" spindle for cut sheet development and thus often one of the first tools used in your bathroom-darkroom for cut sheet film developing. Unfortunately...
thingiverse
A printable replacement for a Tektronix 2400 Series Oscilloscope Foot.
cults3d
Petora Jordan 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
thingiverse
Neuschwanstein 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
thingiverse
Colosseum Roma 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
cults3d
Neuschwanstein 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
thingiverse
Petora Jordan 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
cults3d
Colosseum Roma 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
thingiverse
Firenze Italy 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
cults3d
Firenze Italy 1:2400 for detail...https://sites.google.com/site/tokyovirtualworld/
thingiverse
EN: Holder for Fritz Repeater 2400 Inclined at 20°. ... Very easy Also suitable for the original network cable DE: Halter für Fritz Repeater 2400 20° geneigt. ... Sehr leicht Geeignet auch für das Original Netzwerkkabel
thingiverse
Replacement wing clip for the Phoenix 2400, made it after mine broke. Fits perfectly and is pretty strong, used PLA. ...
thingiverse
This is mausoleum at India For details... ... https://sites.google.com/site/tokyovirtualworld/03-column/28-printed Instructions 1:2400 scale world heritage
thingiverse
Model is made for volantex phoenix 2400. ...The front and rear printed parts are connected by an aluminum T-profile, the size in the photo.
thingiverse
Halterung für einen AVM Fritz! ...Repeater 2400 Das untere Loch ist für ein LAN Kabel Gedruckt mit PLA mit 15% Fill