k40 air assist diy 3d models
116604 3d models found related to k40 air assist diy.thingiverse
K40 Air Assist Takes fish tank air line 3/16 I bought the 8ft 3/16 Penn Plax Airline Tubing for Aquariums for like 2$ amazon. ...
thingiverse
This is a laser cutter nose to add air assistance to your k40 (with stock head) with a 6/4mm air hose. ... It's meant to be cut in 3mm plywood (but anything 3mm should work as well).
thingiverse
Adjustable Air Assist for K40 Nozzle end. ... https://www.amazon.com/gp/product/B085ZTK39M/ (drill this out to 0.6m) Adjustable Air Valve https://www.amazon.com/Aquaneat-Aquarium-Manifolds-Distributor-Control/dp/B07R5RH6WS/...
thingiverse
My take on an air-assist nozzle for the K40 laser engravers. I haven't modified my exhaust vent yet, so had to make endstops to prevent the nozzle from crashing into the vent. ... The attachment hole on the nozzle was designed to be final-drilled...
thingiverse
Air assist nozzle for k40 laser, takes 3mm bolt to clamp onto head. The nozzle tip is held in by friction. The hole at the end of the nozzle tip is very small, unless your laser is well aligned your beam will likely miss this hole, and make its own!...
thingiverse
Air assist for K40 Laser with laser pointer mount. I used #6-32 hardware to attach to pointer mount. The quick connect air fitting threads directly into hole. ... Laser pointer link:...
thingiverse
This is the air assist nozzle I use with my K40 laser cutter. The design was created in OpenSCAD and I have included the OpenSCAD file that can be modified. The coiled hose and fitting I used are listed below. The fitting that I used to attach the...
prusaprinters
Simply solution for install air hose. Possible print without supports. ...New version 2019. Category: DIY
youmagine
This is the air assist nozzle I use with my K40 laser cutter. The design was created in OpenSCAD and I have included the OpenSCAD file that can be modified. The coiled hose and fitting I used are listed below. The fitting that I used to attach the...
thingiverse
Just a simple AirAssist for our beloved K40 Laser. ...Just slide it over ur lensholder and plug in ur air hose, fits really tight, if not there is a small hole u can use for a set screw. ... Made for the use with 6mm OD Silicone hose.
thingiverse
Air assist add on for laser cutter. Uses M3 screw to secure it to laser focusing lens housing and air blows directly on job. ... Air tube is set up so that no support is needed.
thingiverse
Simply solution for install air hose. Possible print without supports. ...New version 2019.
thingiverse
Air Assist / Smoke Assist / Air Nozzle for K40 Laser. Will fit on a standard 26mm OD laser Head and is held in place by two short M3 Bolts. The nozzle has an inlet port designed to fit a 6mm OD PVC tube. ... To make a smaller opening for the air...
cults3d
Air Assist / Smoke Assist / Air Nozzle for K40 Laser. Will fit on a standard 26mm OD laser Head and is held in place by two short M3 Bolts. The nozzle has an inlet port designed to fit a 6mm OD PVC tube. ...To make a smaller opening for the air outlet,...
cults3d
Air assist air duct and bracket for a K40 laser. ...Using a 12v axial fan.
thingiverse
Air assist air duct and bracket for a K40 laser. ...Using a 12v axial fan.
thingiverse
K40 laser air assist adaper, with 1/4 push In connector threading, upright and angled version
thingiverse
This is my version of the Air Assist Nozzle for the Chinese Laser Cutter Engraver K40. It work great using common fish tank tubing. ...
thingiverse
... issues, as well as restores the original friction mount that should lessen concerns about cracking the lens. ... The OpenSCAD source requires Air_Assist.stl from [VanBot112's K40 40W Laser Air Assist](https://www.thingiverse.com/thing:2421971).
thingiverse
Adaptor to fit Air assist and laser diode to the head of the K40. Laser diode is sight for 50.8mm. ... Requires: 2x M3 square nuts 2x M3x8mm screws 1/4" BSP press air fitting 5v laser diode
thingiverse
Hi, This is my version of an Air-Assist Nozzle for the common K40 Lasercutter. It is intended for a 6mm outer dia. air hose. ... The 4 tiny air holes in front of the nozzle are directed a little bit into the direction of the center.
thingiverse
This is an air assist nozzle for a K40 Chinese laser cutter, based on the original model by VanBot112 and the remixed version by Venomouse. I changed the air inlet so that it comes in from the side because I'm using the [positioning laser mount by...
thingiverse
An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...
thingiverse
The was an attempt to design an air assist nozzle for the K40 printer. The nozzle works with the existing laser head and attempts to utilize lamar flow. So far I have had decent success with it but have not tested to see if has increased my cutting...
thingiverse
Die beiden Teile sind die simple Konstruktion eines air assist für einen K40 Chinalaser. Als Luftzufuhr habe ich einen 8mm (6mm innen) Druckluftschlauch genommen und den durch eine Schleppkette mit 10x10mm gezogen (Amazon). Bei mir steckt ein...
thingiverse
The parts I remixed: Air assist by mbridak.: https://www.thingiverse.com/thing:869652 K40 Fan from sebecam2000, which was a remix of K40 Fan from d4d13. https://www.thingiverse.com/thing:2724230 universal tube creator with holder from Winne. ... ...
thingiverse
This thing is a custom made air-assist nozzle for the popular K40 laser engraver/cutter. It mounts on the stock head. The STL has a 1/4NPT thread for pressure air quick connect and a side hole for M3 brass threaded insert to secure the assembly onto...