keter shed door parts 3d models

I bought the KETER shed with a completly broken door hinge. They did not supply the replacement for this. So I was designing a replacement. I had to remove the remnant of the old hinge and glue this one on place with Loctite. I was filling up...

... Lastly, you'll need some boards to use as a shelf. If this worked for your shed, there are other accessories for this shed that can be found in this collection: https://www.thingiverse.com/elfie2002/collections/keter-plastic-shed-organization

These are slot-in self-locking hooks, loops and clips to fit a Keter shed. They use the grooves in the side of the shed. Simply slot in and turn 90 degrees. There is also a spanner to help as they can (by necessity) be quite tight. ... There's a basic...

These are slot-in self-locking hooks, loops and clips to fit a Keter shed. They use the grooves in the side of the shed. Simply slot in and turn 90 degrees. There is also a spanner to help as they can (by necessity) be quite tight. There's a...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9jZOBXB3CLi Made for Keter APEX 8x6. ...It replaces the original latch and fits both at the top and bottom on the inside of the door.

... corner shelf brackets of the same shed. As I continue designing things to improve my organization of this keter plastic shed they will be going into this collection: https://www.thingiverse.com/elfie2002/collections/keter-plastic-shed-organization.

OK, this one is probably very specific as it's designed to fit a specific type of llght, but if you have a Keter shed and need a solution, this might help you out. There is an internal clip mount to hold the light to the ceiling strut and an...

<p>Made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9jZOBXB3CLi Made for Keter APEX 8x6. ...It replaces the original latch and fits both at the top and bottom on the inside of the door.

... then it seems likely. As I continue designing things to improve my organization of this keter plastic shed they will be going into this collection: https://www.thingiverse.com/elfie2002/collections/keter-plastic-shed-organization.

This was a model of a shed door used to manufacture the door stop and door lock, for a man who could not bend over.

Door hook to fit in the holes present in the back of the Keter Factor shed door - useful for hanging small lightweight items (e.g. ...cycle helmets) Update - following a couple of failures in use, I've revised the design slightly - this is the v2...

Had to move my Keter shed and one of the door pins snapped the end off in the process, I didn't have a spare so I decided to knock one up in fusion 360. I think the threads are still a little bit big but the big screw holes I put in allowed me to...

The sliders for the door are Treco/Keter type so the handles probably are too. Can't guarantee they'll fit you shed but the mounting holes are spaced 2.5cm appart so check that against yours. Has holes to put a padlock through. ... This is the...

My Keter Plastic Cabinet was missing a hinge on one of the Bi-fold doors so I designed and printed one. Not sure of the model of the cabinet, Didn't find anything similar on google search, might be an old discontinued model, You will know if you...

this design is to hold shed door inplace so wind does not slam it shut.

Sliding door handle for garden shed. I redid the handles on my own garden shed, as these had broken. ... Hopefully, they can be useful to you.

Replace the hanger on metal shed doors. One has holes that can take inserts and screws. ...Kinda like rebar.

Fastens onto the corner of the shed and the door clips into it. Keeps the door from swinging around in the breeze. ... Print at 10% infill, no supports

This is one of the little things you use to hold the door of a garden shed on a rail to shift it left and right. I drew two versions of it for a friend and printed it in 3djake's ecopla green. ...So far it holds, the white part in the picture is the...

The stock door handle of our garden shed broke, which was the reason to create my first stl. ... Maybe some else can use it too.

The sliders can be purchased as part of a "tune up kit" from the manufacturer here (http://www.sheds.com/miva/merchant.mvc?Screen=PROD&Store_Code=S&Product_Code=DK100&Category_Code=A), or you can save $15 and print your own. At its simplest the...

Luckily the RFID range easily went through the window of my shed so I designed a case to hold it in the corner of the window and then a case to hold the raspberry pi and relay switch. I use a solar power system in my shed and I already have a lot of...

The sliders can be purchased as part of a "tune up kit" from the manufacturer here (http://www.sheds.com/miva/merchant.mvc?Screen=PROD&Store_Code=S&Product_Code=DK100&Category_Code=A), or you can save $15 and print your own. At its simplest the...

Got a shed from a neighbour with a broken door slider. now its fixed. ...added the openscad too just incase you wanted to add to it Print Settings Printer Brand: RepRap ...

... tiny hulk strength to break the handles off of my shed, so I designed some new ones. ...I don't know how universal they are, and maybe some time i will work on a customizable one, but for now these are for the 10 x 12 shed that Lowe's carried in 2017.

This is a design for holding door open so the wind will not slam it in shut. ...Print in petg so if has enough flex for repeated use.

My entry to Azad Balabanian’s Door Scanning Challenge on Twitter: https://twitter.com/Azadux/status/1138447825577136129 Created in RealityCapture by Capturing Reality from 316 images in 00h:19m:48s.

Used on garden sheds with sliding doors. Install factory roller in the top hole and attach to each door. ...2 required per door.

... revised to print more easily. The parts we installed on the shed are the "Modified for Printing" revision. ... I printed this with the round pips that stick out down, parallel to the print bed, matching the orientation of the Thingiverse render.

... revised to print more easily. The parts we installed on the shed are the "Modified for Printing" revision. ... I printed this with the round pips that stick out down, parallel to the print bed, matching the orientation of the Thingiverse render.