kingkong 90gt 3d models

These are Prop guards for the KingKong 90gt micro brushles racing quad. ... Thei are mounted under the motors and not under the frame.

Camera protector from my indoor racedrone Kingkong 90GT The blackparts are printed with MP flex45 material. I think the best choice. ...Print Settings Printer Brand: BCN3D ...

Lipo mount / tray for the KingKong 90GT micro FPV racing quad. Perfect fit for 2S 850 mAh lipos from Hobbyking ( http://bit.ly/2sR2epi ) which give a flight time of ~7 minutes with the KingKong. The two small hooks on the opening of the tray can...

This is a bracket to mount a small 200mw VTX camera on a KingKong 90GT micro drone. I knocked out a quick design before the camera arrived--I wanted to get it back in the air ASAP. I didn't realize the seven segment LED would be sticking out so far...

This is a bracket to mount a small 200mw VTX camera on a KingKong 90GT micro drone. I knocked out a quick design before the camera arrived--I wanted to get it back in the air ASAP. I didn't realize the seven segment LED would be sticking out so...

A sturdy one piece propeller guard for the Kingkong 90GT. I have printed it in ABS. ...It weighs 15 grams.

i designed this canopy to fit the 90gt with stock components. camera pushes into the hole for a tight fit and hole on top is big enough to press the vtx button with your finger. i did have to cut the part off the top plate that originally stuck out...

The stock mounting holes on the 90GT frame is 19mmx27mm. These adapters will allow you to use a standard 20mmx20mm 4-in-1 ESC and flight controller. You will need to thread the holes with a M3x0.5 tap. Then use M3x6mm nylon screws and standoffs. ...

... I've accounted for that in the uploaded object, but I won't know if it's perfect until I crash the quadcopter and need another replacement soon._ This is a remix of [patshead's KingKong 90GT Camera Mount](https://www.thingiverse.com/thing:2359531).

Angled camera mount for KingKong 90GT. Replaces stock VTX mount plate that camera is glued to. 4 camera angles provided, 15deg, 20deg, 25deg and 30deg. Top plate is wide enough to mount the VTX and FrSky RX side by side. You can still access the...

Update 7/25/17: Added Trays that can fit in the same area that the 90GT is stored.

A quick model to allow me to hang up this tiny drone

motor mount(TPU)

Customized version of http://www.thingiverse.com/thing:1341482 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1341482

Customized version of http://www.thingiverse.com/thing:1230740 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1230740

Fits 9x5.5mm buzzer. ...Secure with hot glue.

Propeller guard ARF Kingkong 90GT 90mm  0,2 ABS print   Glued together with superglue

A plate adapter for the 20x20mm mounting flight controller on kingkong 90gt frame kit,some modification required.

Simple DVR03 camera mount for your 90GT. ... Can be printed on both ABS or TPU.

I printed these guards out of soft pla to fly indoors and dont damage anything ;) They work fine so far. They get fixed with two of the four screws, so the motor will not fall off if you have to change them. ...They also work with normal pla, but with...

motor extenders that use all fixing points make with abs 0.1 for strength n.b edge of frame needs a chamfer to allow room for motor e clip

i needed a mount for my 90gt to mount a runcam split mini youll need longer standoffs to raise the camera out of the propellors if you mount it in front the file with the bar is to glue a camera mount to with the "20x20" file, the bar with for the...

Top plate with an integrated camera mount (15, 25, or 35 deg) and Matek buzzer mount. Should have enough clearance for 2035 props. Must use 15mm standoffs. Best printed on ABS. PLA will work as well. No support needed when printed upside down. ... ...

Propeller guard ARF Kingkong 90GT 90mm 0,2 ABS print Glued together with superglue

this is a lipo mount for 450 mah 30mm x 9.5mm If someone needs another size just writes

Holds up to 12 2S lipo 350 mAh battery v2- widen battery compartments by 2 mm, lower box height to 25 mm and some aesthetic changes. ...

Customized version of http://www.thingiverse.com/thing:2088569 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2088569

... I uploaded is 2mm wider than the bumpers I'm running on my own drone.</p> <p>I printed mine in ABS. We'll see just what sort of crashes they can stand up to. The KingKong 90GT Micro Drone Is Bananas KingKong 90GT Upgrades Category: R/C Vehicles

... of crashes they can stand up to. * [The KingKong 90GT Micro Drone Is Bananas](http://blog.patshead.com/2017/04/the-kingkong-90gt-micro-drone-is-bananas.html) * [KingKong 90GT Upgrades](http://blog.patshead.com/2017/06/kingkong-90gt-upgrades.html)

3D KingKong MergedMesh