kubota rt140 3d models
105 3d models found related to kubota rt140.thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 2 hole_radius = 1.5 flat_bottom = 1 message = kUBOTA font_size = 10 font_thickness = 3 stick_width = 5 Font = write/orbitron.dxf
thingiverse
Kubota keychain. ...Specifically for a Kubota Sidekick. The keys are so small you need a marker so that you don't lose them in the woods. ... Print letters 1-2% smaller than the base, glue with model glue or superglue.
thingiverse
This is a nice keychain of Kubota that can be used to identify your tractor or mower key easier from the rest of your keys. ... Enjoy!
thingiverse
After I took all the California warning stickers off the dash of my kubota sidekick, there was a few feet of weird blank space (no joke, it's insane how many cali only stickers were all over that thing). ...I thought I would fill some of the space with...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: flat_bottom = 2 stick_width = 8 font_thickness = 4 hole_radius = 3 Font = write/orbitron.dxf message = Kubota stick_thickness = 2 font_size = 10
thingiverse
Replacement starter knob for a Kubota compact tractor. ...Uses M5 bolt which screws into the starter shaft.
thingiverse
Small case for a single button switch designed to mount to the grille screws on the center stack of a kubota g1800. ...Printed on Creality CR-10 V3, Hatchbox PETG, 250/80/50, support needed.
thingiverse
The clip that holds down the top of my Kubota shop vac snapped. This is a replacement that works well when printed in Polycarbonate. ...In ABS and PLA YMMV.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: message = Kubota RTV stick_thickness = 2 Font = write/orbitron.dxf font_size = 10 hole_radius = 3 font_thickness = 4 stick_width = 8 flat_bottom =...
thingiverse
I lost one of the knobs from my Kubota mower deck belt shield and decided to try to make a replacement. So far so good. ... Ordered M8 x 12mm L x 10mm OD embedment nuts from Amazon and just used a soldering iron to heat them to push them in.
thingiverse
iPhone X holder that fits on a Kubota BXD-25 tractor. Phone kept trying to fall out of my pocket when using my tractor, so I designed this to hold it in a handy place on the tractor when I used it (having it out in the open vs a pocket lets my BT...
cults3d
This is a replacement cupholder for a Kubota RTV side by side. ...The original ones were made out of rubber and have a tendency to blow out when trailering it at highway speeds.
thingiverse
This box fits in the right hand side fender of a Kubota B series tractor. Remove the blank cover from the fender and replace with this box. ... Print with supports
thingiverse
The local Kubota dealer will not provide information or cross over list for grey market tractors so I was left to come up with my own solution to a pretty simple problem. I like to keep my equipment in the best shape I can so I spent a few minutes...
sketchfab
Ковш MEDIUM-Планировочный 100см Kubota-KX71-3
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
prusaprinters
<p>This I made in Inventor just because I was bored.</p> <p>IPT file is for Inventor</p> <p>STL is for 3d printing</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting printer"><strong>Printer:...
thingiverse
This I made in Inventor just because I was bored. ... IPT file is for Inventor STL is for 3d printing