lab clamp 3d models
56148 3d models found related to lab clamp.grabcad
Lab Clamp assembly + partsIf you download it, don't forget to give it a like! ...:)
thingiverse
An attempt to make a laboratory clamp in the style of the original project that is 3D-printable without support. In the current state clamping can be performed by means of a screw and nut through the respective holes. ...This does not give good...
grabcad
Typical retort clamps and stands found in a chemistry lab. ... Reasonable level of detail
thingiverse
Customized version of https://www.thingiverse.com/thing:2452870 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2452870
thingiverse
Customized version of https://www.thingiverse.com/thing:2452870 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2452870
thingiverse
Customized version of https://www.thingiverse.com/thing:2452870 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2452870
cults3d
This is a great clamp that you can build at home to hold you lab glassware. It is a lot cheaper to make than the $40 ones on eBay! If you would like to see this clamp in action, check our youtube channel where we use it to hold up a glass condenser....
thingiverse
This is a great clamp that you can build at home to hold you lab glassware. It is a lot cheaper to make than the $40 ones on eBay! If you would like to see this clamp in action, check our youtube channel where we use it to hold up a glass condenser.
prusaprinters
This device allows for the connection of standard laboratory stands to metal rods by clamping them with two screws from either end of the central block. The use of this connector will allow the attachment of rods to stands at a right angle or...
thingiverse
Customized version of https://www.thingiverse.com/thing:2452870 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2452870
cgtrader
High quality Science Lab Clamps - Dense Quad Mesh. Basic materials/textures + Arnold redner. ... Maya2020 + FBX included.
prusaprinters
Yes, you can print on glass with the Bambu Lab X1! You need to tweak the start code in the slicer a little bit, because there is no special mouth cleaning area. Reduce the y values over 260 to over 250 in the === wipe mouth === section. ...I have added...
thingiverse
Mansion lab air track clamp. Has a 0.25 in. hole to hold a 0.25 in. ...diameter rod, who would have guessed.
prusaprinters
The clamp part has two separate bodies that you should split and print separately while slicing in PrusaSlicer.Bill of materials3pcs M5x20 DIN 933 hex screw for the stoppers on the axes1pc M5x30 for the clamp1pc M5 nut1pc M8 rod 30cm1pc M8 rod...
thingiverse
Cable management clamp for 25 mm (1 inch) thick lab tables. ... SolidWorks 2013 model file included.
thingiverse
The oven and controller just work well together and made for a nice bit of cheap lab equipment for my niece with just a simple 3D-printed clamp. The result is a pretty slick incubator that’s compact and relatively inexpensive. The temperature...
thingiverse
A clamp for NS 29/32 glassware, it fits very thightly, so you might have to scale it up by a few percent.
cgtrader
Lab Bracket Retort Support Stand.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=46704 Instructions Using the following options: image_scale = 1 height = 5 Font = write/Letters.dxf image = Lab (Dog) cut_hole_in_image = 1 rectangle_width = 80 ring_inner = 3 text2_y = -5...
thingiverse
Use these Cookie Cutters for your next Lab Party Snacks. ... Inspired by: https://www.thingiverse.com/thing:1107820
thingiverse
A secondary clamp may be integrated making it useful as a lab retort clamp. Highly customizable - Pipe Diameter, regular Pipe Cross section, height, wall thickness, companion clamp, adjustable clamp phase. ... Requires a bolt or bolts of the...