lectric xp controller 3d models

Lectric XP eBike LCD Cover V1

Protective case/cover for LCD display on Lectric XP 2.0 ebikes.

Re-designed off of Lectric XP 2.0 Airtag Mount by josowe1812 Simply added void to fit a Tile in same mount.

This was created due to some concern of dirt and grime making its way into the key slot of the Lectric XP Lite. ...Designed for TPU filament only.

Apple Airtag taillight mount for Lectric XP 2.0 E-Bike - Recommend using PETG or ABS filament so it can handle the outdoor heat Supports: Recommended Walls: 4 Infill Density: 10%

This was created to avoid scratching the floor with the metal kickstand of the Lectric XP Lite. Will need to be rotated 90 degrees before printing. Just add a zip tie to fully secure the cover to the kickstand. ...Designed for TPU filament only.

Apple Airtag taillight mount for Lectric XP 2.0 E-Bike- Recommend using PETG or ABS filament so it can handle the heatSupports: RecommendedWalls: 4Infill Density: 10%

These are brackets to use with your Lectric XP 2.0 ebike and the Bigant crate that is a popular option to put on the back. The bracket uses 20mm M5 threaded knurled knobs that thread into the existing holes in the rear rack. I printed and use this...

Remixed to fit the throttle on a Lectric XP - as I recall the linked thing was too large. It's just a friction fit on the rubber twist throttle. Print it off, remove right hand grip, and slide the thumb-throttle onto the twist grip. Find a good...

This project is for the Letric Xp 2.0 to add 12v light strips that interface with the existing screws and headlight connection. It uses a dc to dc buck converter to stepdown from the 48v battery to 12v for the LEDs. This part is an eclosure to house...

Firstly, I AM NOT RESPONSIBLE IF YOUR BATTERY IS DAMAGED WHILE USING THIS MODEL OR IF YOU FORGET TO LOCK YOUR BATTERY INTO THE BRACKET This model is designed to hold a Lectric XP Step through spare battery on the back rack. It bolts into the rack and...

Mount a $10.00 Milk Crate from “The Container Store” SKU#: 280070 to the rear rack of a Lectric XP 2.0 eBike using the stock rear rack. I you want to mount a Milk Crate to a Rad Mini see here: https://www.thingiverse.com/thing:4945668 I have...

For the Lectric XP 2.0 comfort seat you will need to print the following: 1 x AirTag Holder 1 x Holder Top 1 x Top Base 1 x Bottom Base For other bike seats you will need to print the following: 1 x AirTag Holder 1 x Holder Top 1 x Top Base...

I used the universal mount on my upgraded Cloud 9 seat successfully. The Airtag must be firmly snapped into the Airtag Holder component prior to installing the Holder Top component. For the Lectric XP 2.0 comfort seat you will need to print the...

I used the rear mount from "thing:4964679", but the front mount would not work with our crates: Milk Crate Mount Lectric XP 2.0 Rear Rack eBike https://www.thingiverse.com/thing:4964679 Designed new front mount for our "Milk Crate" from Home Depot. ... ...

I took this original design, imported into Blender and added some bevels as the originator had suggested.

This is  a basic key fob for Lectric E-bikes 20% in fill 

I call this the Lectric phone holder, but really it will work with any bar of similar diameter. Its two parts, bar clamp and phone pocket. The phone pocket is specific to my phone, buy you can remix if needed. ... The bar clamp can be used to mount...

This can be used to cover the second battery connector on a Lectric Expedition if you do not have a second battery. it can also be used to interface a second battery that you place on the rear rack ot on the down tube. The second top has a...

This is a cover for the Lectric Ebike's display. It is not waterproof. I did use supports for the slot on the top and the lip on the bottom. I printed it face down. It attaches by putting the bottom lip behind the bottom of the display and...

This is a cover for the Lectric Ebike's display. It is not waterproof. I did use supports for the slot on the top and the lip on the bottom. I printed it face down. It attaches by putting the bottom lip behind the bottom of the display and...

I made a GoPro mount for my Lectric XP 2.0 ebike, it might fit other bikes with the same mounts but not sure. I printed mine in TPU after ones printed in PLA had a tendency to rattle a bit while in use. ... You could mount a camera on the front of...

... from moisture. I use it when hauling the bikes to keep the display from getting scratched. This is a full cover and obscures the screen while in place. NOT SURE WHY, there is no images of it in the post but there is when you search lectric 2.0

LOGO XP

OARS-XP.

Copy of the remote control holder of the XP Deus, my original piece was broken. The design is slightly modified compared to the original for more solidity. Personally I used a fill rate of 100% to maximize the strength, but you can surely put a...

comb xp 3d model

Support of the detector metal XP ORX. .../ Support canne pour détecteur de métaux XP ORX

another little robot, Instructions please rescale and rotate the parts.... ...have fun...

#XP-81 ##The Plane That Flew Backwards--Once...Maybe On 1 April 1944, the United States Army Air Force (USAAF) issued a requirement, ORD-20912848374/1220-(ABC)-49032-(XYZ) for an extended-range fighter/ground attack/escort aircraft. As stated in...