lightsaber blade holder 3d models

Bracket designed to hold the blade of a Disney light saber when not in Hilt. Simple Print, No special settings. If you found this useful, please donate what you think it is worth to my paypal.me/Br3ach3r Help cover the time of design. Thanks,...

I Needed a Blade Holder for my Plumbers Pipe Built Lightsaber so here is what I Printed The Pipe has an Inner Diameter of 32mm and the Lightsaber Blade was 1" in Diameter so this Slots Inside the 32mm Pipe and the Blade fits Inside it. The Pictures...

Most generic Lightsaber Hilts will fit any thing around a foot and with a diameter of 1 inch or less

These are modified parts for the Grand Inquisitor lightsaber created by CaseStudyno8 (https://www.thingiverse.com/thing:1945665) to allow insertion of 1" inch saber blades (day blades). This does not allow for electronics, just an empty blade. ...

Threw together a quick PCB holder on Tinkercad because I didn't have any that fit my blade correctly. ... Designed to fit a 7/8" Thin Wall Transwhite blade from TCSS.

This is a lightsaber blade tip for a lightsaber blade with 1" OD you could put a dime on the inside to reflect the light from the lightsaber

Blade cover for the [collapsable lightsaber](https://www.thingiverse.com/thing:3606120) with [removable blades](https://www.thingiverse.com/thing:5339067) The blades stay within the lightsaber but this covers them up and snugly fits to ensure they...

It is a bit wider at the bottom.Lightsabers which use this blade are:Lily Tora Asi's LightsaberNinth Jedi LightsaberHigh Republic Inspired LightsaberReath Silas' LightsaberHiltI've also included model files for the components I use to add this blade...

Collapsible Lightsaber Blade that can be printed in vase mode, extends to 110 cm, and can be used with hilts such as [this](https://www.thingiverse.com/thing:3606120) or [this](https://www.thingiverse.com/thing:3668138). Print each segment of the...

This is a blade for the Collapsing Lightsaber (Removable Blade) by 3DPRINTINGWORLD. The segments are separated from each other to help aid in the printing in case your printer can't handle the clearances. ...This will allow the blade to extend and not...

... wall. This design holds the blade 14mm from the wall which should be average for most hilts. The clip is designed for 25mm blades. Also, the blade clip doesn't support any load so screws aren't necessary. ...I'm using the 0.5lb Command Hook tape.

... with 0.84 widths, and TURN OFF elephant foot compensation or it leaves a lip on the inside.  printed at 0.4 layer heights.the rest of the files are available at https://www.prusaprinters.org/prints/3721-collapsing-lightsaber-removable-blade

these stl files create an Anakin Skywalker Lightsaber with an extendable blade that retracts into the handle the hilt is split into 4 pieces that can be glued together but some of the pieces will just fit without glue. the blade stl file doesn't...

Collapsible Lightsaber Blade that can be printed in vase mode, extends to 110 cm, and can be used with hilts such as this or this.Print each segment of the blade separately, and easily assemble.Read more at...

... would be a bit of fun. ...This blade plug will fit most or all Ultra-saber hilts(~25.5mm wide). The completed plug is roughly 58mm tall and sits just under the top of my lightsaber's emitter(This dimension can vary between the types of hilt styles).

:-) Additional Collapsing Swords: [Pirate Sword][pirate] [Broadsword][broad] [Katana][katana] [Dagger][dagger] [Lightsaber (Print in Place)][light] [Sith Lightsaber (removeable blade)][sith] [Jian (Print in Place)][jian] [Bo Staff][bo] I have some...

Being an avid sabersmith myself, I thought "hey, you could totally make a telescoping lightsaber blade plug from that" So I did just that. I didn't reuse the original files, so this isn't a remix, but it is heavily influenced by 3DPRINTINGWORLD's...

This is a blade for the Collapsing Lightsaber (Removable Blade) by 3DPRINTINGWORLD. The segments are separated from each other to help aid in the printing in case your printer can't handle the clearances. ...This will allow the blade to extend and not...

I had weird issues with blobs and zits at retraction which I normally don't have until I turned on "wipe" and "coast", I'm still using S3D.Detailed printing instructions can be found on my website.I think this is a result of the thin walls with a...

... I also included the original model I made based on a picture of the lego lightsaber piece. It's not scaled to fit an actual minfigure. The blade test and handle test pieces are small test pieces used to see if the parts will fit together.

So there is a scaled collapsing blade included in this thing to be usde with this version of the model. The second version is longer to fit the original collapsing blade. The scaled down blade is 168mm tall during printing. The scaled hilt is 155 mm...

The blade plug is mostly hollow throughout but to prevent dust from entering the lightsaber there are a couple of layers in between which cover the hollow tube completely but still allow the light to pass through. Suggest you print using the same...

A custom 1" blade plug. ...Should fit in any standard 1" blade port.

A custom 1" blade plug. ...Should fit in any standard 1" blade port.

 I wanted to mount it on the wall similar to the wall mount/display stands that came with the Force Fx sabers but could not find one that would hold the hilt with the blade attached.  So, I measured the one I had and did my best to design one in...

Hey guys! ...Here's the tip I use of my lightsabers, it is designed for a 1.25" polycarbonate tube from Menards, and a 1/4" wooden dowel. ...Happy printing!

Replacement blade for STW legion miniatures and variants, also suitable for action figures.

This is a quick blade plug I designed. ...It's 1 inch in diameter and about 2 inches tall.

I've seen many blade stocks were out of the parametric blade caps, and that they only had bullet tips. so i designed one for my resin printer, i will likely make a mold and cast them. ...currently designed to fit inside a diffusion tube.

... 4mm shell. The bottom should attach to a hole made for one inch wide blades, 24mm wide holes would provide for the best fit. I am planning on printing this in da Vinci jr.'s clear yellow filament or clear blue. ...This is just the blade, not a hilt.