linear plus 3d models

this is a remix design for my 2 new anycubic linear plus printer, it really reduces vibration and prints perfectly

Anycubic Kossel Linear Plus effector for Mix-Color Extruder 2 in 1 Hotend from A10M A20M M201

Anycubic Kossel Linear Plus effector for Mix-Color Extruder 2 in 1 Hotend from A10M A20M M201

Nice looking covers for the stepper motors on the Anycubic Linear Plus. Prints upside down to get a glossy surface (using glass bed). ...Recommended to use concentric on first layer.

... ...Printed in PLA with 0.3mm resolution, 10% infill. Tested on Anycubic Linear Plus, should work with Anycubic Linear and other Kossel and Delta printers. As transparent panel I used an acrylic sheet 1m x 0.5m cut in 3 pieces of 0.33m x 0.5m.

This one is a brand new design for a complete plexiglass enclosure for an anycubic kossel linear plus. I was looking for any way to close the printer, so I can heat up the chamber for printing nice ABS parts. ... This thing is not done yet - I...

The PSU mount that comes with the Anycubic linear plus delta printer mounts the PSU straight across the corner of the printer, you cannot mount it on the side of the corner extrusion so it either shoves the PSU into your face or if put on the back...

Use this to mount an E3Dv6 on you Anycubic Linear Plus. I made it so that it fits with the default components, standard effector. After mounting the E3Dv6, the bed levelling sensor does not fit anymore. ...This can be solved by using my bedlevel...

Umbau Anycubic Kossel linear plus Träger für Motherboard, Mosfet. Für TriGorilla Motherboard. Inspirit durch https://www.thingiverse.com/thing:2220058 und https://www.thingiverse.com/thing:3682859 Umbauten geschehen auf eigene...

Now you can just click under the "Other" when adding your printer and there you will find "Anycubic Linear Plus" listed. Here are some basic instructions to make this profile work for you: (EDIT: Change the "x" in Cura 2.x, 3.x, and 4.x to with...

Now you can just click under the "Other" when adding your printer and there you will find "Anycubic Linear Plus" listed. Here are some basic instructions to make this profile work for you: (EDIT: Change the "x" in Cura 2.x, 3.x, and 4.x to with...

ANYCUBIC KOSSEL LINEAR PLUS MAGNETIC LED LIGHTING

Legs for the Anycubic kossel delta 3d linear plus

Anycubic Kossel Linear Plus Füße Dazu benötigt man 12x M4x8mm Zylinderschraube 12x Hammerkopfmutter 3x Filzgleiter

Heatbed Supports to clamp the added height when using the Anycubic Ultrabase on the Anycubic Kossel Linear Plus.

Corner Bracket for Kossel Linear Plus, includes Holes for the T-Nuts so you can slide it over the Frame. ...

Heatbed Supports to clamp the added height when using the Anycubic Ultrabase on the Anycubic Kossel Linear Plus. ...

This is simple tight fit level probe holder for Anycubic Kossel Linear Plus. ...Installed on 2020 frame.

Support for the electronics of the Anycubic Kossel linear plus. ...Recommend to print also the fan support for electronics cooling.

This is corner cover / motor cover for anycubic kossel linear plus printer. ...These are to be used with https://www.thingiverse.com/thing:2620272

Support plateau chauffant (220 mm) + plateau verre (240 mm) pour Delta Anycubic Linear Plus. ...Print Settings Rafts: No Supports: ...

This is reduction from circular heated bed to square coating glass for Anycubic Kossel Linear Plus. It supports original screws and nuts. Autocalibration after instalation is mandatory. ...

Simple holder for Small hercules glue stick.Designed for anycuboc linear plus but it is possible for any 2020 profile.

Heatbed Supports to clamp the added height when using the Anycubic Ultrabase build plate on the Anycubic Kossel Linear Plus printer. ...Cura reports the file is not watertight but it prints fine.

Feet for the Anycubic Kossel Linear Plus that use racquetballs to reduce transmitted vibration. I used Penn Ballistic 2.0 racquetballs, purchased from Amazon. ...A second version of the mount uses squash balls instead of racquetballs.

Feet for the Anycubic Kossel Linear Plus that use racquetballs to reduce transmitted vibration. I used Penn Ballistic 2.0 racquetballs, purchased from Amazon. ...A second version of the mount uses squash balls instead of racquetballs.

Couldn't find an arm/rod damper for Anycubic Kossel Linear Plus arms so I made one, clips on nicely and won't slip. ... Will fit any kossel with 6mm arms.

Heatbed Supports to clamp the added height when using the Anycubic Ultrabase build plate on the Anycubic Kossel Linear Plus printer. ... Cura reports the file is not watertight but it prints fine.

Remix de las tapas de esquina para la AnyCubic Kossel Linear Plus para poder usarlo con los refuerzos de esquina https://www.thingiverse.com/thing:2620272 Lo que he hecho ha sido añadirle agujeros para pasar los tornillos de los refuerzos hasta el...

An incredibly trivial little 3D-printed accessory for your Anycubic Linear Plus... that makes it reassuringly easy to see at a glance how filament is feeding/retracting. This little pointer (seen in light blue here) simply pushes onto to shaft of the...