ls log turbo manifold 3d models

16vt manifold A2 chassis Turbo back 3inch exhaust

LS Exhaust Manifold .375 thick Flange

Turbo manifoldModelled and simulated in SolidworksRendered in keyshothttps://www.youtube.com/watch?v=6uc2hIqJBs8https://www.youtube.com/watch?v=j9Ko9puwc7I

log manifold honda d-serie

Manifolds and Carburetors for LS V12. Carbs 45 DCOE by ATS (Thanks). ...Carbs are wrong for application but they look cool.

2jz turbo manifold

Intake Manifold Turbo

equal length tubular turbo manifold for ls1

mini ram turbo manifold for honda d16

Custom turbo manifold for old engine M20B25.

Turbo manifold to suit a mazda familia 1500cc engine to subaru VF14 turbo

Simple turbo manifold for T3and T4 turbosCredit to Andrey Chernorot for the 3076 used for mockup and the picture.

4-cyl turbo manifold Scaled for 1/24 but size can be changed Intended for personal use, not to be redistributed without consent

Im working on an "electric fan" model to set the turbo back a bit farther for electric fan trucks These are templates designed to assist in the fabrication of a turbo manifold for Chevrelot, and GMC pickup trucks/suvs. ... Bill of Materials: Flanges...

Intake manifold for Suzuki Hayabusa turbo project. With fuel rail and four extra injectors controlled by Power Commander. ...Currently have found a better solution and this is not being used anymore.

Turbo ManifoldApplication of CFD simulation - see results

This is the manifold I'll be using for my 16 cylinder engine, the engine has 4 of these as it's gonna be quad turbocharged :D

I started following a Solid works engine tutorial, but the featured turbo chargers weren't corrrectly modelled, So i decided to custom make them Hope you enjoy :)

hard to print on normal 3d printer as one piece, also included turbo split if u have problems printing it as one, the half turbo files scaled got messed up, 11% is around where it should be for the 2jz engine model also comes with added hood dump i...

Here is a prototype exhaust manifold for my homemade Racecar Project. It will Also work if you have a Hayabusa Race Bike. ...Hope you like it and have a great day!

adaptor to weld pipe to to make custom risers for LS engines with marine power manifolds

Nissan 1400 Champ Turbo Manifold

Inlet manifold for use in a turbocharged application. ...Gives plenty of clearance for low mounted turbos

This turbo manifold was built for a Chevy Sonic to run an aftermarket turbo. ...The runner are equal length and the outlet flange is a T3.

Turbo exhaust manifold for Volvo B230 engine. Equal length primaries (365mm) and divided T3 flange.Designed in NX's routing application. Rendered with Keyshot.Self-made from designing to welding.Made for Volvo 140 series, most likely will fit 164 as...

my first upload! ...im building a old datsun with a new motor and needed a turbo flange to testfit my exhaust! ...enjoy the part

I'm planning on putting twin turbos on a car I have. I took the measurements from a 2002 GMC sierra (5.3 liter lm7) this will probably work on a lot of other gm engines. Like I said I haven't got to try them so I'm not sure if they will work, but I...

Audi 1.8t b5 turbo manifold flange, may have to change the DXF for specific jobs

Turbo Exhaust Manifold that can be assembled to the Turbocharger, it has the same joint dimensions

Turbo manifold flange for the T6 framed Twinscroll turbos, Based on Garrett Dimensions. 12mm thick. Ideal for mocking up tolerances before committing to buying the real deal. ... Can provide other formats for fabrication on request (additional charge...