lulzbot filament 3d models

Filament tube holder for the Lulzbot (mine is a TAZ 5). Keeps the tube upright, preventing filament from flexing until it breaks. ...This replaces the stock tensioner part so it is easy to bolt on.

I noticed that the filament guides on my Lulzbot printers were getting chewed up being pulled into the extruder so I created a small cap to fit over the end of the nylon tubing. This provides a stronger end while also preventing it from being pulled...

After about 1800 hours on the Taz5 since last July, I started getting some slip on the filament pressure tab, I thought it might be due to the radius on the bottom of the Lulz stock tab. This is square on the edges, seems to hold solid again, it may...

After we made the tabletop spoolholder for the Taulman and Filament Central spools, we realized that our Lulzbot spools were too big so we had to make a bigger one. The reason we had to make these at all was because when they shipped our Z-Morph...

Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: just about anything Infill: 15-25% Notes: Make sure you lay it on its back so you don't need to print the supports; I probably should rotate it in the STL files,...

Lulzbot Universal Filament holder . This holder clamps on to the frame of the Lulzbot Taz. It uses 5/16 all thread and 4 608ZZ bearings. Update: You will need 4 - M3-.5 3.8mm Heatset Insert and 4 M3 socket head cap screws. ... Insert the heatset...

The Lulzbot Mini has a rectangular arm for holding the filament spool. The spool drags on the arm and causes a jerky motion of the spool. Others have designed spool holders for the Mini to alleviate this problem. Here is my version. The bolt is a...

So I closed up 4 sides of my Lulzbot Mini and restricted the top to a 1.75" slot for access to the filament clamp on the extruder and also obviously to allow an unrestricted path for the filament to the extruder. This modification allows you to...

Print Settings Printer Brand: LulzBot Printer: Mini Rafts: No Supports: Yes Resolution: 0.250 Infill: 85% Notes: I printed it standing up using buildplate support because I wanted the inserts to have a bit more tensile strength. I cut one centimer of...

Remixed rjelbert's filament runout switch and filament guide so that I would not require 2mm screws. ... I added two 2mm posts that hold the switch in place, as well as a cover that secures it in place with 2 3mm screws and nuts.

With the far right placement of the filament spool on the mini you can end up with the filament getting pulled to some pretty extreme angles with respect to the hobbed bolt assembly. I found I was ending up with the occasional jam or skip due to this...

Here's the original writeup: With the far right placement of the filament spool on the mini you can end up with the filament getting pulled to some pretty extreme angles with respect to the hobbed bolt assembly. I found I was ending up with the...

This is a remix of Ender 3 Filament guide by daGHIZmo on October 17, 2020. It's not elegant but it does the trick. I used things I already had e.g. zip ties, washers and bolts. ...I also attached it to the Mini frame with 3M adhesive foam tape.

I saw a filament ring guide that was threaded for the TAZ6 here on Thingiverse and thought it was intriguing but didn't like the bends or angles the tube on my printer would need to make. Anyway I thought ok my tube flops around a lot so let me make...

Using different filaments such as clear, and older filament, I would find that sometimes it would snap due to the sharp angle when using the standard holder. I quickly drew this up and printed it on my Lulzbot mini. It works beautifully! ...

Have enjoyed the performance Lulzbot TAZ printers have, but noticed that the flexible filament guide can get sucked into the idler arm if you are using a grippy or rough filament. This boot fits on the end of the guide and prevents it from being...

The Lulzbot Mini comes with a spool holder that's rectangular in cross section. As the spool unwinds, it sometimes hangs, or moves abruptly. Some say that this causes intermittent tension on the extruder that can lead to wavy lines or other print...

A modification of moerice's design (https://www.thingiverse.com/thing:2863986). ... This remix makes it possible to install the guide with the filament still loaded. ...The angled slot prevents the filament from coming out on it's own.

This filament spool holder should work with any Taz printer. There are other similar spool holders, but I made mine with a few ideals. Minimalistic design to avoid wasting material and taking up space Simple to install without needing excessive...

For Lulzbot TAZ Mini and any other Wade 3D printer extruders that require an 8mm spacing between the face of the idler and the edge of the ridged section of the idler tension screws. How I Designed This We started with a smaller jig Lulzbot created,...

... and created a Tension Jig for my Lulzbot Mini, but wanted it to have more of a Tool-like shape. ...No jokes, please ;) Print Settings Printer Brand: LulzBot Printer: Mini Rafts: No Supports: No Resolution: 0.25 Infill: 85%

We have a few of the Lulzbot Mini 3D-printers at West Warwick High School and wanted to redevelop the way that the machine holds the spools of filament that it uses. The two arm pieces attach to the back of the device and the bar snaps in between...

I took the awesome spool holder design by Dereksunday and modified the mount to fit the new Sidekick. ...It still has the guides for zip ties as well as holes for mounting with screws.

About the problem of the square spool holder of our Mini. I share a remix of the original by Greg Grieves (ggrieves). Fits perfectly on the Mini 2, and runs smoothly rolls of 1kg and 3kg. I just extended it a little to cover all the spool holder,...

I had noticed the jerky behavior in unspooling filament during prints on my Lulzbot Mini, so I was glad when I came across the thing this is based on. However, the inner diameter of the filament spools I used was smaller. I created this design to...

Starter CAD for filament guide between stepper motor and hot end. very early efforts. ...Feel free to improve upon this WORK IN PROGRESS.

This part is a filament sensor enclosure for LULZBOT TAZ 6. ...

Instructions 5 - 608ZZ Bearings 5 - M8x20 Hex Cap Bolts 5 - M8 Nuts 10 - M8 Washers 2 - M3 Heat Inserts 2 - M3x20 Bolts 2 - M3 Washers 2 - 5mm Wide Zipties Printed Parts 5 - 3mm Filament Wheel.stl 5 - Nut.stl 1 - Plate v2.stl 1 - Tube Holder.stl 1 -...

.gcode - print this if you don't want to think, these settings are the ones that I found the most usable .factory - slicer3d file if you want to tweak how I generated my gcode .f3d - fusion 360 design files if you want to tweak my design See here...

Instructions Obviously printed on my Lulzbot TAZ 4 in PolyMAX from PolyMakr (specialty PLA with great strength and flexibility characteristics. Given the small size, and the expected stress on the part, I printed at .1mm layers, 3 shells, 35%...