m lok battery holder 3d models
499400 3d models found related to m lok battery holder.thingiverse
These are picatinny rail and/or M-LOK mounted spare battery holders. Great option for keeping spare batteries for your scope, red dot, flashlight, or other accessories with you all the time. These are designed to use a 0.060" section thickness...
cults3d
These are picatinny rail and/or M-LOK mounted spare battery holders. Great option for keeping spare batteries for your scope, red dot, flashlight, or other accessories with you all the time. These are designed to use a 0.060" section thickness...
thingiverse
M-Lok Flashlight holder. This is designed for the $13 flashlight (588 Lumen) that they sell at Harbor Freight. https://www.harborfreight.com/588-lumen-tactical-flashlight-63934.html You'll need to get M-Lok screws (Amazon has them) and you'll also...
prusaprinters
M-Lok Flashlight holder. This is designed for the $13 flashlight (588 Lumen) that they sell at Harbor Freight. https://www.harborfreight.com/588-lumen-tactical-flashlight-63934.html You'll need to get M-Lok screws (Amazon has them) and you'll also...
thingiverse
This is Flashlight holder for Magpul M-LOK interface. Flashlight mount dia. ~18 - 28 mm. 1. 2x Ziptie 2. 1x Rubber (35 x 18 x 1 mm) 3. 2x Screw M5 x 12 4. 2x Washer body 5mm 5. 2x Nut M5 13.01.2018 Added ver.2 Это крепление фонаря для...
thingiverse
This is a shell holder (3 shells) for caliber .45-70 Government with M-Lok rail mounting holes.
prusaprinters
... tension might be a little different for PLA. ...You will need to print with supports as the underside is not flat.You will also need a pair of M-Lok screws and nuts.I also have a 2 magazine holder version with an improved locking and release design.
prusaprinters
This M-Lok compatable shell holder holds 3x shells in the vertical position. Included is the step file incase you want to edit/remix. ...I specifically made this for airsoft but it can be used for real-steel.<br><br>Recommended filament: PETG</p>
prusaprinters
This is my redesign of the edgun leshiy magazine holder for use with M-LOK rails. I have a single mag holder version up here as well.This version has some subtle improvements over the original design. It is intended to be printed in PLA+ for the...
thingiverse
Here a small Picatinny rails and holder for my favorite flashlight with a diameter of 20 millimeters. I created the regular version and version 2 with better mount. I used two 16 millimeter M4 bolts, but you can use shorter bolts. For flashlight...
thingiverse
... ... The cap is held in place via friction as well as 6 small 4mm Dia X 1mm Neodymium magnets, providing a solid grip this is attached to the recessed M-Lok in the side of the carbine, it has enough room to not interfere with the folding stock too.
prusaprinters
Simple, single 12 gague shotshell holder to give sporting shooters that one last round to complete a stage (when you miss that last critical shot - we've all done it!).This is a remix based on glompos21 design on Thingiverse.I've modified the design...
thingiverse
this is for the pre-tapped holes in the side of the ACC chassis from MTD just above the mag-well if you don't have pre tapped holes and you just want to put it on an M-LOK slot you are going to need some lugs, I might add those later if anyone asks...
thingiverse
basic m-lok nut. ...used about 14 of these to hold some basic m-lok covers on.
thingiverse
Corrected height of M-Lok posts for grip to be flush with gaurd. ...Hardware for M-Lok can be purchased online.