m2 ssd bracket 3d models

m2 ssd

Radiator M2 SSD

M.2 2280 SSD Storage bin for x10 added lid per *[ranhalt](https://www.thingiverse.com/ranhalt/about)* request

M.2 SSD to be used by close up renders of computers, notebooks or other IT equimpment. Contains textures with UV mapping. ... Texture resolutions: 4096x4096 PCB (diffuse, specular, bump, normal) 3072x3072 Chips (diffuse, bump) 1024x1024 Resistors /...

Bracket for fitting a 2.5" SSD into a 3.5" HD bay

I might do some minor tweaking in the future including a design with less material and different concepts for mounting the SSD inside the bracket. The holes for the screws have a diameter of 4mm each, so almost any computer screw will fit. ... This...

This bracket holds a regular sized ssd in the 2u rack. It can be mounted on the ends or between other modules. ... The holes are a bit tight so ream/file them out or use a hammer :p (just kidding, don't use a hammer!) The ssd can be mounted with the...

Housing for USB SSD M2 adapter. ...

... save materials. Holes have been made a little larger to make it easier to pass through. The horizontal holes have been made so that they do not collapse during printing. Two types of SSD mounting positions (center and side) can now be selected.

I wanted to cover my M2-disc but the one I found felt a bit to close to the disc so I modified it and doubled the distans to the disc. ...Original from here: https://www.thingiverse.com/thing:2652094

Design an 2.5" SSD mount for a M2 USB holder

Airplane Bearing Bracket M2

Simple SSD Bracket design for a PC build that did not have Drive trays

Got a nice m2 cooler that was compatible only with 2280-size ssds, so I've made this little adapter to fit a 2242 ssd that I already own

This case holds RPI 3 with X806 M2 SSD shield - http://www.suptronics.com/miniPCkits/x860.html. ... It's a little bigger than original case so only provided top fits.

Created a set of the SSD adapter

Makergear M2 Fan Bracket for use with fan shroud thing:69327

Created this dual SSD bracket to be compatible with the Fractal Design F2 case. It will probably be compatible with others if they support a water cooling pump mount. Thought some people might find it useful if they don't intend on water cooling and...

I bought a M2 enclosure and needed a way to carry the included USB cables along with it.

I bought a M2 enclosure and needed a way to carry the included USB cables along with it. Category: Computer

An SSD bracket to hold internal SSD drives for a MacPro 2019. Print flat on the build plate no need for supports or rafts - ensure the thicken portion is on top. Updated Jan 7 - had to shorten the holes for the SSD - didn't realize it would be...

An SSD bracket to hold internal SSD drives for a MacPro 2019. Print flat on the build plate no need for supports or rafts - ensure the thicken portion is on top. Updated Jan 7 - had to shorten the holes for the SSD - didn't realize it would be...

I had a P75 Dell Laptop that when picked up the M.2 SSD would shift and slip out from under the screw that holds it. I designed this little shim that removes the gap allowing it to slip out of its slot, and adding a lip that stops it from being able...

An SSD holder to fix it vertically in a custom setup. ... Screw holes are 3mm wide.

An SSD holder to fix it vertically in a custom setup. ... Screw holes are 3mm wide.

A mount I designed to mount a SSD to the underside of a table.

10 bay variant of the SSD Stack0r by h3nkGer which was a revision of the original 2/4 SSD mount by colanabo. ...Approximate dimensions are 94.5mm x 10mm x 119mm

M2 fan bracket that attaches the 50mm and 40mm fans to the extruder. ... Based off the single bracket by tomlombardi Ran through netfabb and ready to print, will be updating with an led spot.

This allows a standard 3.5" hard drive to be swapped out of a computer and replaced with two 2.5" SSD drives stacked into the same space.

Bracket for Silverstone SG13 for a side mounted PSU