mateksys 3d models

Adopted this to fit with the Mateksys F765 Flight Controller.

some cable protection and led clip all in one. ...use TPU for best result LED controller i used :http://www.mateksys.com/?portfolio=2812-ctrl

This is a holder for the Mateksys GPS. It should be mounted on the back of the FPV drone. It is designed to fit on 5mm diameter frame spacers. Made for the TBS source ove V3, but fits on almost every drone that has the 5mm diameter frame spacers.

AOS 7 Support for Mateksys M8Q GPS.

This is a quick mount I drew up for the Mateksys Optical Flow Sensor. ...Fits at the rear of the Speedybee 5 HD V1 nicely.

Matek system power distribution board FCHUB-6S

It can be hot glued into foam planes, or it can be screwed into wood planes with a US #4 wood screw or similar. The top lid securely snaps into the base, but can be separated again with a bit of force. It is designed to remain secure in flight,...

use this guard to mount your mateksys 2812 LED's onto the arm of your street league quad. ... you can use double sided VHB tape to both attach the print to the arm and to attach the LED to the print.

Mateksys GPS mount for Xilo slammed Freakstyle Quadcopter

Mateksys M8Q-5883 GPS holder for the Iflight Nazgul5 v2 copter

This is a case for a mateksys F405-STD and M8N GPS I pulled from a Radiolink TS100

Based on the original iflight STL-Files for the DJI-Airunit version of the iflight Protek35 i made a version with an integrated GPS-Mount for the Mateksys sam-m8q GPS module.

... an GPS holder which fits my needs so i designed a new one. ... I used TPU printing this, and double-sided tape on the bottom of the GPS module. Fixed with an ziptie, which also fixes the wires underneath. Its a MATEKSYS GPS & COMPASS MODULE M8Q-5883

Note that the Mateksys screws need to be changed for longer M2x8mm length screws. Also note that the antenna holder must be printed flat, and not in the shown position here. Last Comment : The pictures were made on previous iteration of the...

Remix of FPV_tiger's mounts for use with Mateksys M8Q-5883 GPS Sensor

Frsky R9 slim+ and mateksys L0X 3901 lidar mount for the readytosky ZD550 frame. Uses two small 3mm wide zip ties to install. Part was SLA printed on a anycubic photon, not tested currently printing, ill update with an install video or edit when i...

i don't use a gopro so i merged the two source files together to achieve what i needed...

Box for installing the matek video transmitter in the wing! ... For installation you need 4 screws

For Martian II frames, which have MatekSys H-LED with buzzer installed at the back. ... It ventilates, holds firmly in position, no possible shorts to GND.

For Martian II frames, which have MatekSys H-LED with buzzer installed at the back. It ventilates, holds firmly in position, no possible shorts to GND. Print instructionsCategory: R/C Vehicles Print Settings Printer Brand: Prusa Printer: Prusa Mk2...

After losing GPS modules during crashes with previous builds, I designed this bracket to mount the Mateksys M8Q-5883 GPS module on the top-front of the iFlight Cidora SL5 and Titan XL5 frames. The existing M3 screws are long enough to secure the...

Wing cover for the tube MATEKSYS ASPD-4525

To hold the Mateksys M8Q-5883 GPS module

Wing cover for the tube and sensor MATEKSYS ASPD-4525

Simple part that helps to hold my VTX and RX antennas in place, as well as the GPS. ...The GPS module that I have is a mateksys M8Q-5883 http://www.mateksys.com/?portfolio=m8q-5883. ... Printed in TPU.

A simple holder to mount the a GPS like Mateksys M8Q-5883 at the back of an iFlight Nazgul5 V2.

This is a mount for a M8Q-5883 GPS/Compass module from Mateksys, specifically for DJI F450 frames.

Arm protection for Armattan Badger/Marmotte frames with slot that fits a "mateksys 2812 led strip slim".

Mateksys ASPD-4525 Airspeed sensor mounting. ... Designed to be aerodynamic and lightweight, with cables hidden (cut into EPO/EPP).