mentos freshmaker 3d models
78 3d models found related to mentos freshmaker.cgtrader
Mentos are a brand of packaged scotch mints sold in stores and vending machines. First produced in 1932, they are currently sold in more than 130 countries worldwide by the Italian-Dutch corporation Perfetti Van Melle. ...The mints are small oblate...
thingiverse
Put your roll of Mentos into this handy dispenser that twists shut so that your mints will not fall out again! Requires no supports or rafts. ... This is a public project you can also view on...
grabcad
A high poly, high detail model of a Mentos tablet. Modeled in 3ds max 2010, rendered with V-ray1.5. Materials included. ... Made by Maarten_Dominicus 20/1/2012
pinshape
This holds 5 Mentos (more than enough for a 15+ft fountain) and has two 1mm holes for a paper clip to fit through to keep the Mentos from falling. A screw head easily attaches to the two liter bottle with a tapered nozzle on the opposite end. Tie a...
thingiverse
instructions 1. ...put pin in hole 2. fill with mentos 3. run tripwire 4. ...wait
myminifactory
This is my Cola-Mentos powered Mini-Rocket. ...It there are two peaces which are connected by a threat. Just put the coke inside the Rocket, screw the Parts together and throw the mentos into the can. Have Fun! ...:-)
thingiverse
Just a container that holds exactly 4 pieces of Mentos gum that I take to work with me.
thingiverse
Mentos attachment Everyone of us surely knows the experiment with mentos and coca cola when coca-cola subsequently foams. Of course, not everyone succeeds to make the geyser several meters high. By throwing one candy after another by hand, we never...
thingiverse
Mentos attachment Everyone of us surely knows the experiment with mentos and coca cola when coca-cola subsequently foams. Of course, not everyone succeeds to make the geyser several meters high. By throwing one candy after another by hand, we never...
thingiverse
A rig for mentos and Coca Cola experiments. ... See it in action at: https://www.youtube.com/watch?v=Cq-1VQTyurw
thingiverse
Made a slightly longer version that can hold 10 mentos. Here's a video I made featuring the nozzle. ...https://www.youtube.com/watch?v=swTocjsbRq4
thingiverse
Remix of drcameron's Mentos Nozzle Cannon. All I did was extend it to make it longer to be able to use more Mentos. Instead of just scaling it on the z axis, I cut and spliced it to make it longer. ...This way the threads stayed the same as the original...
thingiverse
●Use the parts below magnet(磁石) Φ6mm x 3mm x1 O ring(Oリング) aboutΦ22mm *See photo(写真参照) plastic wrap(サランラップ) Suitable magnet for hold(適当な磁石) mentos(メントス) x3 coke(コーラ) x1 ●Assemble in the order below 1. Glue the magnet to the holder-pats ...
thingiverse
This holds 5 Mentos (more than enough for a 15+ft fountain) and has two 1mm holes for a paper clip to fit through to keep the Mentos from falling. A screw head easily attaches to the two liter bottle with a tapered nozzle on the opposite end. Tie a...
thingiverse
I was asked by a family member to make a Mentos/Coke bottle launcher nozzle thing. BUT they also wanted it to simulate a Minecraft TNT explosion. ... https://www.youtube.com/watch?v=Ig-wiTRGDPc It uses a 3mm allen wrench as a launch key I was...
thingiverse
assembly - glue the two parts together and load with Mentos (i glued them in as well), drill a 1/2 in hole centered in the bottle cap and spot glue the tray in place. launch - drink or dump a small amount of the diet coke so that the cap can be...
thingiverse
I wanted to design a mentos rocket that when you drop the mentos in then it takes off! ZOOM! Print in PLA or ABS should be fine. Make sure to put supports on the base, but not in the tubes because you want those clear and clean. The diameter...
thingiverse
Fill tube with mentos, place a pin in the little hole to hold them in.. screw on to a bottle (2L most likely preferred for maximum spray). Then watch the soda spray! I barbed the end of the tubes to allow hoses to be attached. The outer diameter...
thingiverse
We have a post that explain how this thing work:https://www.yoctopuce.com/EN/article/coke-mentos-yoctopuce-fun Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Doesn't Matter Supports: No Resolution: standard Infill: 10%...
thingiverse
This is the video with the cannon pictured here with the round top http://www.youtube.com/watch?v=6PLzzKISAuI Here is a printable version that screws on top of the 2 liter Coke bottle to hold the ammunition (Mentos). Install the safety pin once (...
thingiverse
[>>>] Generating Attributions log: [0] Thing Title : Mentos-Diet Coke Spray Head [0] Thing URL : http://www.thingiverse.com/thing:100563 [0] Thing Author : Weldingrod1 [0] Thing Licence : Creative Commons - Attribution [1] Thing Title : Venus de Milo...
myminifactory
Mentos and Coke Rocket, load the mentos into the lid and slide a paperclip into the hole to hold them in place. put the bung in the bottom and fill the base with coke. Twist the lid in place and pull out the paperclip then run... ... Ive had limited...
myminifactory
Place mentos (or other catalyst ingredient) into the nose cone, and hold in place with the "pin". Place the rocket over the opening of a Diet Coke (or other reactionary liquid) and pull the pin to release! ...Object may need to be scaled to fit snuggly...
thingiverse
... strings. Partially straighten a paperclip, leaving a loop. Tie a long string onto the loop. Drop in your Mentos, stick in the paperclip, and screw it onto the Diet Coke bottle. ... Step back (if you want to stay dry), and pull the paperclip out!